Abstract:In this research, the mechanical behaviors of extruded AZ31B Mg plate along normal direction (ND) were investigated over a wide range of strain rates. High strain rate tests were carried out using a split Hopkinson pressure bar at room temperature. The corresponding deformation mechanisms, texture evolution and microstructure changes were analyzed by utilizing optical microscope (OM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). It is found that the mechanical responses exhibit both sigmoidal hardening and power-law hardening behaviors under compression at high strain rate ranges of 1068-5647 s(-1). The prismatic type textures of the skin layer and center layer of the AZ31B plate determine its mechanical behaviors. The sigmoidal hardening behaviors are resulted from the formation and development of {10-12} extension twinning at the initial stage of deformation. Whereas the power-law hardening behaviors are resulted from non-basal < c+a > dislocation slip dominated the deformation at the initial deformation stage. Experimental results indicate the critical resolved shear stress (CRSS) for extension twinning and non-basal < c+a > dislocation slip are insensitive to strain rate, but the latter CRSS is significantly higher than the former CRSS. The flow stress is insensitive to strain rate if plastic deformation is dominated by extension twinning, while it increases with the increase of strain rate if plastic deformation is dominated by nonbasal < c+a > dislocation slip. Dynamic recrystallization (DRX) took place if the AZ31B plate was compressed at strain ranges of 4737-5647 s(-1), resulting in a decrease in flow stress and a significant increase in ductility. (C) 2016 Elsevier B.V. All rights reserved.

Microstructure and Deformation Mechanism of AZ31 Magnesium Alloy under Dynamic Strain Rate

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

Effects of Micro-Twin Lamellar Structure on the Mechanical Properties and Fracture Morphology of AZ31 Mg Alloy

Twinning and Dynamic Recrystallization in AZ31 Magnesium Alloy under Medium-High Strain Rate

Mechanical Behavior and Microstructural Characteristics of Magnesium Alloy Containing {10-12} Twin Lamellar Structure

Characteristics of Hot Tensile Deformation and Microstructure Evolution of Twin-Roll Cast AZ31B Magnesium Alloys

Tensile Behavior and Microstructural Evolution for AZ31 Magnesium Alloys Sheet at High Strain Rate

Coupled Influence of Temperature and Strain Rate on Tensile Deformation Characteristics of Hot-Extruded AZ31 Magnesium Alloy

Plastic Deformation Mechanisms of AZ31 Magnesium Alloy under High Strain Rate Compression

Deformation Behavior of Hot-rolled AZ31 Magnesium Alloy During Tension at Moderate Temperature

Temperature and Strain Rate Dependence of Deformation Microstructures of Az31 Magnesium Alloy under Uniaxial Tension

Influence of Rolling Speed on Microstructure and Mechanical Properties of AZ31 Mg Alloy Rolled by Large Strain Hot Rolling

Influence of Microstructure and Mechanical Properties on Formability in High Strain Rate Rolled AZ31 Magnesium Alloy Sheets

Deformation Microstructure and Characteristics of Cast-Rolling and Normal Rolling AZ31 Magnesium Alloy Sheets

Dynamic mechanical response and microstructural evolution of extruded Mg AZ31B plate over a wide range of strain rates

Influence of strain rate on microstructure and formability of AZ31B magnesium alloy sheets

Microstructural evolution and dynamic recrystallization model of extruded homogenized AZ31 magnesium alloy during hot deformation

Deformation behavior and microstructure transformation of AZ31B Mg alloy under high strain rate compression

Anisotropy of deformation localization under high strain rate loading of AZ31 magnesium alloy plate

Influence of strain rate on dynamic recrystallization behavior of AZ61 magnesium alloy

Deformation behaviour of AZ31 magnesium alloy sheets produced by twin-roll casting and sequential hot rolling