Abstract:High-temperature proton exchange membrane fuel cells (HT-PEMFC) possess distinct technical advantages of high output power, simplified water/heat management, increased tolerance to fuel impurities and diverse fuel sources, within the temperature range of 120-200 & DEG;C. However, for practical automobile applications, it was crucial to broaden their low-temperature operating window and enable cold start-up capability. Herein, gel-state phosphoric acid (PA) doped sulfonated polybenzimidazole (PBI) proton exchange membranes (PEMs) were designed and synthesized via PPA sol-gel process and in-situ sultone ring-opening reactions with various proton transport pathways based on absorbed PA, flexible alkyl chain connected sulfonic acid groups and imidazole sites. The effects of flexible alkyl sulfonic acid side chain length and content on PA doping level, proton conductivity, and membrane stability under different temperature and relative humidity (RH) were thoroughly investigated. The prepared gel-state membranes contained a self-assembled lamellar and porous structure that facilitated the absorption of a large amount of PA with rapid proton transporting mechanisms. At room temperature, the optimized membrane exhibited a proton conductivity of 0.069 S cm-1, which was further increased to 0.162 and 0.358 S cm-1 at 80 and 200 & DEG;C, respectively, without additional humidification. The most significant contribution of this work was demonstrating the feasibility of gel-state sulfonated PBI membranes in expanding HT-PEMFC application opportunities over a wider operating range of 25 to 240 & DEG;C.& COPY; 2023 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by ELSEVIER B.V. and Science Press. All rights reserved.

Layer by Layer Self-Assembly Fabrication of High Temperature Proton Exchange Membrane Based on Ionic Liquids and Polymers

Novel Cross-Linked Membranes Based on Polybenzimidazole and Polymeric Ionic Liquid with Improved Proton Conductivity for HT-PEMFC Applications

Composite Membranes Based on Polybenzimidazole and Ionic Liquid Functional Si–O–Si Network for HT-PEMFC Applications

Polybenzimidazole/ionic-liquid-functional Silica Composite Membranes with Improved Proton Conductivity for High Temperature Proton Exchange Membrane Fuel Cells

Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

PEMs with High Proton Conductivity and Excellent Methanol Resistance Based on Sulfonated Poly (aryl Ether Ketone Sulfone) Containing Comb-Shaped Structures for DMFCs Applications

Gel-state Polybenzimidazole Proton Exchange Membranes with Flexible Alkyl Sulfonic Acid Side Chains for a Wider Operating Temperature Range (25–240 °C)

Achieving Better Balance on the Mechanical Stability and Conduction Performance of Sulfonated Poly(ether Ether Ketone) Proton Exchange Membranes Through Polydopamine/polyethyleneimine Co-Modified Poly(vinylidene Fluoride) Nanofiber As Support

Mechanically Robust and Highly Methanol-Resistant Sulfonated Poly(ether Ether Ketone)/poly(vinylidene Fluoride) Nanofiber Composite Membranes for Direct Methanol Fuel Cells

Construction of High-Performance, High-Temperature Proton Exchange Membranes through Incorporating SiO2 Nanoparticles into Novel Cross-linked Polybenzimidazole Networks

Diazoniabicyclo-type Poly (ionic Liquid) Cross-Linked Polybenzimidazole Membrane with Improved Phosphoric Acid Retention for HT-PEMFCs

Fabrication of an ultra-thin and ordered SPEEK proton exchange membrane by in Langmuir-Blodgett self-assembly process

Ionically Crosslinked Composite Membranes from Polybenzimidazole and Sulfonated Poly (fluorenyl ether ketone) for High-Temperature PEM Fuel Cells

Design of sepiolite-supported ionogel-embedded composite membranes without proton carrier wastage for wide-temperature-range operation of proton exchange membrane fuel cells

Electrospinning-assisted Construction of Rapid Proton Conduction Channels in Halloysite Nanotube-Encapsulated Ionic Liquid-Embedded Sulfonated Poly(ether Ether Ketone) Proton Exchange Membranes

Sulfonated poly(ether ether ketone)-Protic ionic Liquid-Based anhydrous Proton-Conducting composite polymer electrolyte membranes for High-Temperature fuel cell applications

Novel High Temperature Proton Exchange Membranes Based on Functionalized Poly(arylene Dimethylamino Benzene) Polymers

An imidazole-philic dispersible ionic liquid provides ample proton transport channels and high proton performances for high temperature proton exchange membranes

Soluble ultra-high molecular weight poly(4,4′-diphenylether-5,5′-bibenzimidazole) based membranes with remarkable mechanical strength and specific proton conductivity for high temperature proton exchange membrane fuel cells

Spacer-engineering construction of continuous proton transport networks for cardo poly(biphenyl indole) high-temperature proton exchange membranes

Construction of Stable Wide‐Temperature‐Range Proton Exchange Membranes by Incorporating a Carbonized Metal–Organic Frame into Polybenzimidazoles and Polyacrylamide Hydrogels