Abstract:This paper concerns the thermal performance of a high temperature packed bed thermal energy storage (TES) system containing carbonate salt based composite phase change materials (CPCMs) that made of a eutectic carbonate salt of NaLiCO3 (phase change material, PCM), MgO (ceramic skeleton material, CSM) and graphite flakes (thermal conductivity enhancement material, TCEM). A rectangular packed bed configuration containing CPCMs bricks is built and a three-dimensional computational model is established to study the thermal performance of the system. The enthalpy-porosity approach and surface-to-surface (S2S) radiation model are respectively adopted to model the phase change process and the radiation heat transfer inside the system. A ferric oxide is also used as the sensible heat storage material to compare with the CPCMs based system. The numerical model is first compared with the published experimental data and reasonably good agreements are obtained, indicating the confidence of the model. Extensive modelling is then performed under different conditions to investigate the effects of various parameters including the radiation heat transfer, TCEM mass loading and heat transfer fluid (HTF) operation conditions on the system performance. The results indicate that the system containing CPCMs shows better charging and discharging performance in comparison with the system containing ferric oxide due to the large energy storage density and high thermal conductivity. The thermal radiation has an important influence on the system performance. The system heat transfer efficiency is apparently enhanced when the radiation heat transfer influence is taken into consideration. When the emissivity is at delta = 1, the total charging period of the system is respectively shortened by 10.6% and 25.7% than that of the emissivities at delta = 0.5 and delta = 0. The use of TCEM in the CPCMs significantly enhances the heat transfer performance of the system. An increase in the TCEM loading from 0% to 30% respectively leads to the reduction in charging and discharging processes by almost 30.3% and 29.2%. The results also indicate that, for a fixed charging/discharging power, both the overall charging and discharging periods of the system decrease with the increase of Re number or decrease of Ste number since an increase in the Re number (decrease in the Ste number) leads to an overall enhancement of the heat transfer between the HTF and the CPCMs bricks and hence an overall improvement in the charging and discharging rates.

Numerical Comparison Between Single PCM and Multi-Stage PCM Based High Temperature Thermal Energy Storage for CSP Tower Plants

Optimization of Thermal Performance in Thermocline Tank Thermal Energy Storage System with the Multilayered PCM(s) for CSP Tower Plants

Evaluation of PCM Thermophysical Properties on a Compressed Air Energy Storage System Integrated with Packed-Bed Latent Thermal Energy Storage

Dynamic Thermal Performance Analysis of a Molten-Salt Packed-Bed Thermal Energy Storage System Using PCM Capsules

Numerical Investigation of the Melting Temperature Effect on the Performance of Thermocline Thermal Energy Storage Tank for CSP

Influence of The PCM Volume Fraction on the Thermal Performance of Thermocline Thermal Energy Storage Tank Used in CSP Plants

Numerical Study to Investigate the Thickness of the PCM Layer for the Three Layers Tank for the CSP Plants

Numerical Simulation Research on Thermal Energy Storage Characteristics of a Cascaded Packed Bed with Phase Change Material

Performance evaluation of a solar thermal storage system proposed for concentrated solar power plants

Design of Sensible and Latent Heat Thermal Energy Storage Systems for Concentrated Solar Power Plants: Thermal Performance Analysis

Optimization of the packed-bed thermal energy storage with cascaded PCM capsules under the constraint of outlet threshold temperature

Experimental Study on the Thermal Performance of High-Temperature Shell-and-Tube Molten Salt Phase-Change Thermal Energy Storage

Thermo-economic Evaluation of PCM Layer Thickness Change on the Performance of the Hybrid Heat Storage Tank for Concentrating Solar Power Plants

Performance investigation on the cascaded packed bed thermal energy storage system with encapsulated nano-enhanced phase change materials for high-temperature applications

Thermal performance analysis and optimization of cascaded packed bed latent heat storage tank

Investigation on the Thermal Performance of a High Temperature Packed Bed Thermal Energy Storage System Containing Carbonate Salt Based Composite Phase Change Materials

Thermal Performance Analysis of Multi-Layer Thermal Energy Storage Tank Using Different Phase Change Materials

Thermal Performance Analysis of Thermocline Combined Sensible-Latent Heat Storage System Using Cascaded-Layered PCM Designs for Medium Temperature Applications

Review and characterisation of high-temperature phase change material candidates between 500 C and 700C

Heat-Storage Performance Optimization for Packed Bed Using Cascaded PCMs Capsules

Numerical Study of Thermal Conductivity Effect on The Performance of Thermal Energy Storage