Abstract:In recent years numerical simulation has become one of the most important means to study the complex oil flow within gearbox. Since the gap between tooth surfaces near the gear mesh zone is quite tiny, it’s difficult to get high quality mesh grid near such zone. Further numerical divergence frequently occurs along iterative process with dynamic mesh. To overcome this predicament, some researchers have tried different gear modeling methods to simplify the gear model, such as none-teeth method, cutting-teeth method or gear-separation method. Nevertheless these methods have certain limitation. This paper attended to provide a new practical gear modeling methods called teeth-face-moving method. The method was operated by moving each tooth surface slightly. As the tooth thickness was marginally reduced, the gap between tooth surfaces near the mesh zone was increased to 0.5-1 mm, so that mesh generation in the gap became feasible, which was different from the previous methods, i.e. all of teeth profiles and the center distance of 2 gears were kept as same as the original when using the teeth-face-moving method. To certify the reasonability of this new method, a numerical model for splash lubrication in gearbox was built with different gear modeling methods. The volume of fluid (VOF) method was applied to track the air and oil two-phase flow. And RNG k-ε model was introduced to describe turbulence flow considering high fluid strain rate and high bending degree of flow line. Standard wall function was applied to deal with the flow near wall region and low Reynolds number flow. Dynamic mesh method with the spring-based smoothing and local remeshing was used to adapt the motion of gears. Due to more concentrating upon mesh zone, the gear-separation method and the teeth-face-moving method required more grid elements and computational resource than other methods. The numerical results of oil distribution and gears’ churning loss were comparatively analyzed. Also the simulated results were made a comparison with the existed experiment data. It was easily observed the quantity of oil splashed by gears with none-teeth method or cutting-teeth methods was obviously less than that with gear-separation method or teeth-face-moving method. The similar phenomenon was acquired from churning loss results as well. The churning loss computed with none-teeth method or cutting-teeth method was far less than the related experimental result. On the contrary the churning loss computed with gear-separation method or teeth-face-moving method showed good agreement with the related experimental result. The direct reason was tip diameter and teeth profile had a strong influence on the oil flow in the gearbox. So cutting all or partial teeth may lead unreliable simulation result for splash oil flow. It seemed that the gear-separation method got the result close to the teeth-face-moving method. Unfortunately the center distance of 2 gears had to be increased for the gear-separation method. This was unacceptable in real engineering case because changing the position of gear may lead to related bearings or shaft intersected with other structures, such as bearing base and gearbox housing. So the conclusion is drawn that the teeth-face-moving method not only provides more credible prediction for oil flow in the gearbox, but also has more practicability for complicated engineering situation and hence is superior to the previous gear modeling methods. The teeth-face-moving gear modeling method is quite beneficial to lubrication simulation for real engineering gear system, such as truck axle or vehicle transmission. And further work of applying this new method on complicated machinery is underway.

Simulation of vibro-impact gear model considering the lubricant influence with a new computational algorithm

An original numerical calculation method for impacting contact model of spur gear under lightly loaded condition

Effect of lubricant viscosity on dynamics of high-precision gear considering lubricant-induced backlash reduction

Simulation and experiment on vibration of helical gear transmission considering EHD

Dynamic Modeling and Analysis of Spur Gears Considering Friction–vibration Interactions

Dynamic analysis of gear system with multiple lubrication states in torque–speed parameter space

Mesh stiffness and nonlinear dynamic response of a spur gear pair considering tribo-dynamic effect

Nonlinear Dynamic Analysis of Two External Excitations for the Gear System Using an Original Computational Algorithm

The impact of lubricant viscosity to the vibration of gearbox under light load condition

An Improved Dynamic Modelling for Exploring Ball Bearing Vibrations from Time-varying Oil Film

Tribo-dynamic modelling and analysis for a high-speed helical gear system with time-varying backlash and friction under Elastohydrodynamic Lubrication condition

Analysis of Vibration Characteristic for Helical Gear under Hydrodynamic Conditions

Modeling and analysis of transient lubrication characteristic of the helicopter main transmission spiral bevel gears in point contacts

Investigation of the Lubrication System in a Vehicle Axle: Numerical Model and Experimental Validation

Numerical investigation of vibration-induced cavitation for gears considering thermal effect

Gear splash lubrication numerical simulation and validation based on teeth-face-moving method

Integrated wear prediction model for cylindrical gear with variable hyperbolic circular arc tooth trace under mixed elastohydrodynamic lubrication

Influence of vibration on the lubrication effect of a splash-lubricated gearbox

Lubrication Performance of Helical Gear Pair Under Dynamic Load Based on Local Involute Profile

Dynamics Analysis of Spur Gears Considering Random Surface Roughness with Improved Gear Body Stiffness

A Study on the Influence of Nonlinear Vibration on Fretting Damage of Involute Spline Pairs in Aero-Engines