Abstract:Photoelectrochemical water splitting (PEC) is a viable solution for addressing future environmental and energy concerns. However, due to the high cost of photoelectrodes and the limitations of sluggish kinetics, practical applications are limited. To achieve that goal, effective solutions are still needed to create low-cost photoelectrodes suited for PEC. Transistion metal sulfides (TMS) materials have a high potential for use as photoelectrodes due to their favorable and impressive properties 1 . The photoactivity of TMS is typically unlimited due to low reflection at the grain boundary. The individual atomic thin sheets with higher surface area compared to bulk materials allow for faster diffusion of photoinduced charge carriers primarily due to the less interface between their grains. Their lower interfacial contact resistance enables enhanced charge dynamics and, as a result, improved electrochemical reaction kinetics. When compared to other TMS, CdS has a direct bandgap and excellent photoactivity. However, its toxicity and photocorrosion make it unsuitable for long-term practical use. WS 2 is well-known layered transition metal sulfide that has a 2D molybdenite structure. It is non-toxic in acidic/neutral solutions that are chemically stable. It has been demonstrated to be more stable against oxidation and photo corrosion than CdS, which is extensively employed in photocatalysis 2 . However, because of the recombination of photoinduced charge carriers, pure WS 2 exhibits relatively poor photocatalytic efficiency and stability. As a result, combining WS 2 based photoactive nanomaterials with other suitable materials has helped overcome this challenge. Transistion metal sulfides with acceptable band structures for heterostructure construction with WS 2 may enable breakthroughs in photocatalytic and photo-electrochemical processes. The primary focus of this work is to construct heterostructures by combining CdS and WS 2 and to investigate their role as photoanodes of semiconductor materials in PEC water splitting. In this work, we have synthesised heterostructures using a facile solution-reaction method and Successive Ionic Layer Adsorption Reaction deposition (SILAR) technique which is intrinsically cost effective and scalable 3 . The heterostructure is characterised by XRD, SEM and TEM. We also studied the performance enhancement of this heterostructure using Linear sweep voltammetry and Electrochemical impedance spectroscopy. Pristine WS 2 and CdS showed photocurrent densities of 3 μA cm -2 and 20 μA cm -2 . However, heterostructures formation led to much improved photocurrents. Photocurrent densities of 151 μA cm -2 were observed for WS 2 /CdS heterostructures respectively at 1.23 V vs RHE. The enhanced improvement in photoelectrochemical performance in the case of the heterostructures could be due to the following factors: (a) the intimate interaction of this unique heterostructure improves adhesion and lowers the photoinduced charge transfer barrier; (b) increased light harvesting capability; and (c) improved charge dynamics of photoinduced charge carriers due to proper band alignment. The current study paves the way for further research into the creation of metal sulfide heterostructures that generate analogous photoelectrode materials. Keywords: Photoelectrochemical water splitting, metal sulfides, photoelectrodes. Figure 1

Phase‐Modulated Band Alignment in CdS Nanorod/SnSx Nanosheet Hierarchical Heterojunctions Toward Efficient Water Splitting

An Anti-Photocorrosive Photoanode Based on a CdS/Ni X S Y @NF Heterostructure for Visible-Light-driven Water Splitting

Realizing Efficient Photoelectrochemical Performance for Well-Designed CdS@ZnIn2S4 Heterostructure Photoanode with Directional Interfacial Charge Transfer Dynamics

Interface Charge Transfer and Photoelectrochemical Properties of Sns2 Nanosheets/Wo3 Heterojunction

Structure and Band Alignment Engineering of CdS/TiO2/Bi2WO6 Trilayer Nanoflake Array for Efficient Photoelectrochemical Water Splitting

General In Situ Photoactivation Route with IPCE over 80% toward CdS Photoanodes for Photoelectrochemical Applications

CdS/ZnFe2O4 Core-Shell Nanorod Arrays on Modified TiO2 Photoanodes for Photoelectrochemical Water Splitting

Functionalized Cd 0.5 Zn 0.5 S Chalcogenide Nanotwins Enabling Z-Scheme Photocatalytic Water Splitting

Hierarchical Cds Nanorod@Sno2 Nanobowl Arrays For Efficient And Stable Photoelectrochemical Hydrogen Generation

CdS Nanorods with an Optimized ZnS Coating As Composite Photocatalysts for Enhanced Water Splitting under Solar Light Irradiation

Combined CdS/In2S3 heterostructures with cocatalyst for boosting carriers separation and photoelectrochemical water splitting

CdS@Ni3S2 for Efficient and Stable Photo-Assisted Electrochemical (P-EC) Overall Water Splitting

Vertically aligned two-dimensional SnS2 nanosheets with a strong photon capturing capability for efficient photoelectrochemical water splitting

Combined heterostructures between Bi2S3 nanosheets and H2-treated TiO2 nanorods for enhanced photoelectrochemical water splitting

Thickness Tunable SnS Nanosheets for Photoelectrochemical Water Splitting

Highly efficient 3D/0D CdIn2S4/Cu2O photoanode with p-n type heterojunction for boosted photoelectrochemical water splitting under visible light irradiation

Multidimensional CdS nanowire/CdIn2S4 nanosheet heterostructure for photocatalytic and photoelectrochemical applications

Sulfate-Functionalized Core-Shell ZnO/CdS/Ag<sub>2</sub>S Nanorod Arrays with Dual-Charge-Transfer Channels for Enhanced Photoelectrochemical Performance

Tetrafunctional Cu2S Thin Layers on Cu2O Nanowires for Efficient Photoelectrochemical Water Splitting

Enhanced Photoelectrochemical Performance in Engineered Interface 2D Metal Sulfide Heterostructures for Water Splitting

Designing WO3/CdIn2S4 Type-Ii Heterojunction with Both Efficient Light Absorption and Charge Separation for Enhanced Photoelectrochemical Water Splitting