Abstract:A novel multiple‐gradient‐structured medium‐Mn steel is successfully fabricated by cyclic torsion. An outstanding simultaneous improvement in yield strength, ultimate tensile strength, and tensile toughness is achieved in the gradient sample. A persistent transformation‐induced plasticity effect and heterogeneous‐deformation‐induced (HDI) hardening over the entire uniform strain range are conducive to excellent ductility/toughness. The HDI strengthening and dislocation strengthening primarily contribute to the high strength. A multiphase‐gradient‐structured medium‐Mn steel with dislocation/stacking fault (SF) density gradient, austenite fraction gradient, and grain size gradient is designed and fabricated by cyclic torsion. It exhibits higher yield strength (YS) (942 MPa), ultimate tensile strength (1295 MPa), and tensile toughness (290 mJ mm−3) than its homogeneous counterpart (672, 1273 MPa, and 278 mJ mm−3, respectively). High‐density‐interlaced SFs are generated at the surface region because of the change in strain path and stress state during cyclic torsion. These massive interactive SFs promote the persistent martensite transformation of the retained austenite in the surface region within the entire uniform strain range. Therefore, in addition to the central layer, the surface region in the gradient structures provides strong strain hardening. Moreover, the continuous martensite transformation in the surface region allows the gradient structure to be retained even after tensile failure, which is beneficial for improving the heterogeneous‐deformation‐induced (HDI) hardening of the gradient‐structured sample during tensile deformation. Thus, the combination of active and persistent transformation‐induced plasticity effect and HDI hardening contributes to its excellent tensile toughness and ductility. Quantitative analysis indicates that HDI strengthening and dislocation strengthening play a dominant role in the sample's ultrahigh YS.

Increasing Yield Strength of Medium Mn Steel by Engineering Multiple Strengthening Defects

Strong and ductile medium Mn steel without transformation-induced plasticity effect

Towards Strength-Ductility Synergy in a Medium Mn Steel Through Developing Heterogeneous Dual-Morphology Microstructure

A Simultaneously Improved Strength and Ductility on Medium Mn TRIP Steel Designed by Pre-Twinning Strategy Based on SFE Controlling

Experimental Investigation on a Novel Medium Mn Steel Combining Transformation-Induced Plasticity and Twinning-Induced Plasticity Effects

Stepwise Warm Rolling for Synergistic Strength and Ductility Enhancement in Heterolamellar Medium-Mn Steel

Super-High-Strength and Formable Medium Mn Steel Manufactured by Warm Rolling Process

Improving the strength and ductility of medium Mn steel by depleting the stress-assisted martensite

Simultaneous Increase of Both Strength and Ductility of Medium Mn Transformation-Induced Plasticity Steel by Vanadium Alloying

Heterostructure mediated high strength and large ductility in novel medium-Mn steels with low Mn content

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Enhancing the Strength of Medium Mn Steel by Flash Treatment

Ensuring Combination of Strength, Ductility and Toughness in Medium-Manganese Steel Through Optimization of Nano-Scale Metastable Austenite

Superior Yield Strength and High‐Tensile‐Toughness Matching of Medium‐Mn Steel with Gradient Structure Developed by Cyclic Torsion

Strong Yet Ductile Medium Mn Steel Developed by Partial Austenitization

Design of Tri-Phase Lamellar Architectures for Enhanced Ductility in Ultra-Strong Steel

Optimizing strength & ductility combination of medium-carbon TRIP steel via multi-stage work hardening

High-strength medium Mn quenching and partitioning steel with low yield ratio

Enhancing strength–ductility synergy in medium Mn steel with hetero-structured austenite developed by two-stage cyclic thermomechanical treatment and flash annealing

Strong and ductile medium manganese steel processed by low-temperature partitioning

Design of a high strength, high ductility 12 wt% Mn medium manganese steel with hierarchical deformation behaviour