Abstract:Perovskite solar cells based on the inorganic/organic hybrid perovskite have attracted increasing attention over the past 3 years. Many studies have been done in this area. Controling the morphology of the perovskite film is an effective way to improve the photoelectric conversion efficiency of the devices. In our reserch, we studied the influence of structure and morphology of perovskite films on the performance of the organic-inorganic hybrid perovskite solar cells which prepared by a sequential deposition method. Mesoporous TiO2 scaffold were introduced as electron collecting layer. Lead iodide (PbI2) was then spin cast on the TiO2 scaffold. The PbI2 subsequently transformed into the perovskite (CH3NH3PbI3) by dipping the TiO2/PbI2 film into a solution of CH3NH3I. We studied the difference between the PbI2 film with or without drying under room temperature after spin-coating. Through drying under room temperature, larger pores formed in the PbI2 film. While without drying under room temperature, smaller and shallower pores formed in the PbI2 film. The results show that larger pores in PbI2 film leads to more complete transformation of PbI2 to CH3NH3PbI3 and larger CH3NH3PbI3 particles. CH3NH3PbI3 films were prepared with three different processes: (a) direct dipping the PbI2 film with smaller pores into the CH3NH3I solution; (b) direct dipping the PbI2 with larger pores into the CH3NH3I solution; (c) dipping the PbI2 with larger pores into the CH3NH3I solution after pre-wetting. The resulting CH3NH3PbI3 films were studied with SEM, UV-vis absorption spectrum and XRD. The particles size of the CH3NH3PbI3 are 150, 250 and 350 rim for process (a), (b) and (c) respectively. CH3NH3PbI3 films fabricated through process (a) show insufficient absorption due to the insufficient transformation of the PbI2. The pre-wetting procedure leads to slower reaction result in larger CH3NH3PbI3 particle size. Devices with proper size of CH3NH3PbI3 particles show the highest photoelectric conversion efficiency. An efficiency of 13.5% was achieved with a J(sc) of 17.8 mA/cm(2), a V-oc of 1.05 V and a FF of 72.5%.

Zinc Ion As Effective Film Morphology Controller In Perovskite Solar Cells

Anion effect on properties of Zn-doped CH3NH3PbI3 based perovskite solar cells

Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Iodide manipulation using zinc additives for efficient perovskite solar minimodules

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Controlled Crystallization of CH3NH3PbI3 Films for Perovskite Solar Cells by Various PbI2(X) Complexes

Enhanced Photovoltaic Performance and Stability of Planar Perovskite Solar Cells by Introducing Dithizone

Control of the Morphology of PbI2 Films for Efficient Perovskite Solar Cells by Strong Lewis Base Additives

Zinc Aluminum Oxide Encapsulation Layers for Perovskite Solar Cells Deposited Using Spatial Atomic Layer Deposition

Enhanced Performance of Perovskite Solar Cells by Modulating the Lewis Acid-Base Reaction.

Effects of ZnI2 Doping on the Performance of Methylammonium-Free Perovskite Solar Cells

Regulation of Lead Iodide Crystallization and Distribution for Efficient Perovskite Solar Cells

Enhancing the crystallization and optimizing the orientation of perovskite films via controlling nucleation dynamics

Controllable Grain Morphology Of Perovskite Absorber Film By Molecular Self-Assembly Toward Efficient Solar Cell Exceeding 17%

Zinc As a New Dopant for NiOx-Based Planar Perovskite Solar Cells with Stable Efficiency Near 20%

Improved Efficiency and Stability of Perovskite Solar Cells Induced by CO Functionalized Hydrophobic Ammonium‐Based Additives

Influence of Structure and Morphology of Perovskite Films on the Performance of Perovskite Solar Cells

Ligand‐Modulated Excess PbI2 Nanosheets for Highly Efficient and Stable Perovskite Solar Cells

Revealing Size‐Dependency of Ionic Liquid to Assist Perovskite Film Formation Mechanism for Efficient and Durable Perovskite Solar Cells

Improving the Efficiency of Perovskite Solar Cells Through Optimization of the CH 3 NH 3 PbI 3 Film Growth in Solution Process Method

Hydrogen-bond-bridged intermediate for perovskite solar cells with enhanced efficiency and stability