Abstract:A lithium-sulfur (Li-S) battery has a high theoretical specific capacity (1675 mAh g-1 of elemental sulfur) and a high nominal energy density (2500 Wh kg-1 of cell weight), which offers the prospect of a significant energy density improvement compared to the mainstream lithium-ion batteries (150 Wh kg-1). However, the development of Li-S battery technology has been plagued by problems arising from the highly insulating nature of sulfur (5×10-30 S cm-1 at 25 °C), the high solubility of lithium polysulfides in the electrolyte and volumetric expansion of sulfur during lithiation. Here, we demonstrate the design and preparation of few-layer graphene (FLG) foam scaffold for sulfur loading to fabricate cathode structures for lithium-sulfur batteries. In this work, a free-standing FLG monolithic network foam was formed as a negative of a Ni metallic foam template by CVD followed by etching away of Ni. Then, a three-dimensional (3-D) cathode system for lithium sulfur (Li-S) batteries has been synthesised by loading sulfur on to this interconnected network of few-layered graphene (FLG) via a sulfur solution infiltration method. This cathode system did not require any additional binding agents, conductive additives or a separate metallic current collector thus decreasing the weight of the cathode by typically ~20-30 wt%. A Li-S battery with the sulfur/FLG foam cathode shows good electrochemical stability and high rate discharge capacity retention for up to 400 discharge/charge cycles at a high current density of 3200 mA g-1, which due to the FLG foam offers excellent electrical conductivity, an appropriate pore structure for containing the electro-active sulfur and facilitates rapid electron/ion transport. Even after 400 cycles the capacity decay is only ~0.064% per cycle relative to the early (e.g. the 5th cycle) discharge capacity, while yielding an average columbic efficiency of ~96.2%. To further understand the sulfur loading ability of FLG foam, the composites with high content (up to 72 wt %) were also investigated. The composite with high content of sulfur still presented good initial discharge capacity and good cycle stability after 200 cycles. Our results indicate the potential suitability of graphene foam for efficient and high-performance batteries.

Encapsulating Various Sulfur Allotropes Within Graphene Nanocages for Long‐Lasting Lithium Storage

3D Dual-Confined Sulfur Encapsulated in Porous Carbon Nanosheets and Wrapped with Graphene Aerogels As A Cathode for Advanced Lithium Sulfur Batteries

Nano-Sized Graphene Cages Realize Highly Loaded "Solid-Solid" Process in Cathode Materials of Lithium Sulfur Batteries

Template‐Free Self‐Caging Nanochemistry for Large‐Scale Synthesis of Sulfonated‐Graphene@Sulfur Nanocage for Long‐Life Lithium‐Sulfur Batteries

A Dual-Spatially-Confined Reservoir by Packing Micropores Within Dense Graphene for Long-Life Lithium/Sulfur Batteries

Sulfur Encapsulation into Carbon Nanospheres as an Effective Technique to Limit Sulfide Dissolution and Extend the Cycle Life of Lithium–Sulfur Batteries

Confinement of Sulfur Species into Heteroatom-Doped, Porous Carbon Container for High Areal Capacity Cathode

Dual‐Confined Flexible Sulfur Cathodes Encapsulated in Nitrogen‐Doped Double‐Shelled Hollow Carbon Spheres and Wrapped with Graphene for Li–S Batteries

Hierarchical Nanostructured Carbon/Sulfur Hybrid Cathode for High-Performance Lithium-Sulfur Battery

Nanoarchitectured Graphene/CNT@Porous Carbon with Extraordinary Electrical Conductivity and Interconnected Micro/Mesopores for Lithium‐Sulfur Batteries

Self-conversion templated fabrication of sulfur encapsulated inside the N-doped hollow carbon sphere and 3D graphene frameworks for high-performance lithium–sulfur batteries

Confining Small Sulfur Molecules in Peanut Shell-Derived Microporous Graphitic Carbon for Advanced Lithium Sulfur Battery

Co9S8 nanotube wrapped with graphene oxide as sulfur hosts with ultra-high sulfur content for lithium-sulfur battery

Thin-carbon-layer-enveloped Cobalt-Iron Oxide Nanocages As a High-Efficiency Sulfur Container for Li-S Batteries

Ultraﬁne Nanosulfur Particles Sandwiched in Little Oxygen-functionalized Graphene Layers as Cathodes for High Rate and Long-life Lithium-Sulfur Batteries.

Three-dimensional Graphene Framework with Ultra-High Sulfur Content for a Robust Lithium–sulfur Battery

Constructing Monolithic Sulfur Cathodes with Multifunctional N,P Dual-Doped Carbon Nanocages to Achieve High-Areal-capacity Lithium-Sulfur Batteries

Silicon dioxide molecular sieve with mono-layer carbon deposited in the channels and carbon nanotubes on the outside for lithium–sulfur batteries

Enhanced Cycle Performance in a Binder Free Lithium Sulfur Battery Using Few-Layer Graphene Foam Scaffold

In Situ Assembly of MnO2 Nanosheets on Sulfur-Embedded Multichannel Carbon Nanofiber Composites As Cathodes for Lithium-Sulfur Batteries

Reinforced conductive confinement of sulfur for robust and high performance Lithium-sulfur batteries.