The Study of AM/PM Coefficient in Helix TWT

Haijian Qiu,Yulu Hu,Zhonghai Yang,Bin Li

DOI: https://doi.org/10.1109/ivec.2017.8289505

2017-01-01

Abstract:The AM/PM coefficient has been simulated in a C-band Helix TWT with Microwave Tube Simulation Suite (MTSS). The results of the simulation show that pitch and rod width play a significant role of affecting AM/PM coefficient. And the AM/PM coefficient has been reduced by 3.484 deg/dB after optimization.

What problem does this paper attempt to address?

The Study of Group Delay Distortion in Helix TWT

Haijian Qiu,Yulu Hu,Zhonghai Yang,Jianqing Li,Bin Li

DOI: https://doi.org/10.1109/ivec.2014.6857701

2014-01-01

Abstract:The group delay has been simulated and optimized in a high efficiency Ku-band Helix TWT with Microwave Tube Simulation Suite (MTSS). The results of the simulation and optimization show that the first segment of the pitch (p0) and the working voltage (V) play a significant role in affecting group delay. And the group delay has been reduced by 1.14 ns after optimization.
Research of Efficiency Enhancement in a Helix TWT with Simulated Annealing Algorithm

Zhaoyun Duan,Mingyi Lu,Yubin Gong,Yanyu Wei,Wenxiang

DOI: https://doi.org/10.1109/ppps.2007.4346014

2007-01-01

Abstract:Helix traveling-wave tubes (HTWTs) are high-gain high-power broadband vacuum electron devices. Due to their broad bandwidth, HTWTs have been widely used in telecommunication application and electronic warfare systems. The electron efficiency at high frequencies of the operating band has been a major concern with these devices, especially with space HTWTs. Therefore, in this paper, the computational optimization technique of simulated annealing, which has the advantage over conventional optimization techniques, such as a steepest-descent optimization algorithm in that a global optimum solution was be determined, was used to optically design the helix pitch profile. Computational results were presented and discussed. It is shown that the electron efficiency and output rf power can be effectively improved through numerical simulation. In the near future, the method will be utilized to study suppression of harmonic wave and linearity in the entire operating band.
P2-36: Simulation of crossmodulation and intermodulation products of helix TWT using a new 2.5D multifrequency large signal code

baoliang hao,kangsong tang,liu xiao,shi li,m huang,pukun liu

DOI: https://doi.org/10.1109/IVELEC.2010.5503488

2010-01-01

Abstract:A 2.5D multifrequency large signal beam-wave reaction code of TWT based on the field theory is developed for crossmodulation and intermodulation products, in which space charge fields are obtained through solving discrete Helmholtz equations with the help of Particle-in-cell method. Two-tone experiment and simulation of L band space helix-TWT shown that a good agreement in CM and IM products.
Influence of Attenuator on the Performance of the Helix TWTs

Zhaoyun Duan,Yubin Gong,Wenxiang Wang,B. N. Basu,Yanyu Wei

DOI: https://doi.org/10.1109/ivelec.2006.1666233

2006-01-01

Abstract:On the basis of the 1D CHRISTINE, under the condition of attenuator considered, that is, its RF (Radio Frequency) characteristics including attenuation constant, phase propagation constant and interaction impedance taken into account, in the meantime, two different attenuation models set up, the nonlinear properties of beam-wave interaction in the helix TWTs (Traveling Wave Tubes) were analyzed, and the simulation results were compared with both conventional theory and experimental measurements under single signal excitation. The compared results clearly show that it is necessary to consider completely the attenuator's RF characteristics to accurately evaluate the helix TWT performances, especially in the small signal gain and AM/PM conversion.
Numerical Optimization of Pitch Profile Foroverall Efficiency Enhancement of a Space TWT

Hong-Xia Yi,Pu-Kun Liu,Liu Xiao

DOI: https://doi.org/10.2528/pierc10070807

2010-01-01

Progress In Electromagnetics Research C

Abstract:Obtaining higher e-ciency during the development of space Traveling Wave Tubes (TWTs) is always one of the most important goals for scientists. In this paper, a scheme of obtaining the maximum theoretical overall e-ciency is explored by optimizing the helix pitch proflle of a TWT based on the collectability of spent beam. The collectability of the spent beam was evaluated by the maximum collector e-ciency, and this maximum collector e-ciency was employed to calculate the maximum theoretical overall e-ciency. The energy distribution of the spent beam and the output power of TWTs were calculated by the 3-D large signal Beam-Wave Interaction Simulator (BWIS) of MTSS. The detailed design of a Ku-band helix TWT is described according to three optimization goals (theoretical overall e-ciency, theoretical collector e-ciency and electronic e-ciency). The simulation results indicate that the optimization for high interaction circuit e-ciency or collector e-ciency by itself is not adequate to obtain maximum overall e-ciency. The maximum theoretical overall e-ciency of 77% was achieved via the optimization of slow wave structure for theoretical overall e-ciency.
Study the Mechanism and Suppression of AM/PM Conversion of Traveling-Wave Tubes Using Eulerian Hydrodynamic Analysis

Hai-Jian Qiu,Yu-Lu Hu,Quan Hu,Xiao-Fang Zhu,Bin Li

DOI: https://doi.org/10.1109/ted.2018.2868855

IF: 3.1

2018-01-01

IEEE Transactions on Electron Devices

Abstract:In this paper, the fourth-order analytic solution of amplitude modulation to phase modulation (AM/PM) conversion is first derived from an Eulerian nonlinear analytic model. The analytic relationships between electron phases, detuning parameter b, and AM/PM conversion are also found. Then, the mechanism of AM/PM conversion is studied. It is found that the generation of the harmonics in the dc component of the electron phase in the nonlinear beam-wave interaction region is the main mechanism of AM/PM conversion. Next, a series of AM/PM conversion suppression schemes is discussed by using the mechanism. The Eulerian formations are validated by an in-house code based on the Lagrangian theory. Results show that the fourth-orderanalytic solution of normalized axial electric field and AM/PM conversion agree well with the Lagrangian theory in the nonlinear region. In addition, the suppression schemes are applied to a high-efficiency Ku-band space traveling-wave tube (TWT). The AM/PM conversion distortion is greatly reduced by approximately 50%with a slight drop of output power. We hope that our efforts will help the nonlinear design of TWT in the future.
An Improved Optimization Method for Helix Pitch Profile in Twts

YuLu Hu,ZhongHai Yang,JianQing Li,XiaoFang Zhu,Bin Li

DOI: https://doi.org/10.1109/ivec.2014.6857700

2014-01-01

Abstract:An Improved optimization method for helix pitch profile in traveling wave tubes has been described in this paper. Regardless the reflection waves effect, the sequence characteristic of the beam-wave interaction calculation and the power saturation index such as field relative phase are integral to the optimization method. By Setting several backup point and using the field relative phase, the beam-wave interaction calculation for optimization have been cut down. The total optimization time can reduce to 50% approximately. Also the optimal result can be easily achieved by this method.
Efficiency Enhancement of Space TWT based on Collectability

Yi Hong-xia,Xiao Liu,Liu Pu-kun,Li Guo-chao,Xue Zhi-Hao

2010-01-01

Abstract:High efficiency is one of the essential requirements for modern space Traveling Wave Tube(TWT) development,and a single percentage point increase of overall efficiency is very significant to translate into potential revenue increases.The enhancement of overall efficiency was realized by optimizing the helix pitch profile of a TWT to maximize the collector efficiency.The maximum collector efficiency of a TWT normally conflicts with the basic beam-wave interaction efficiency.Such a conflict has been mitigated via setting the electronic efficiency higher than 25% as a constraint of the algorithm to ensure a high output power.The 3-D large signal Beam-Wave Interaction Simulator(BWIS)of MTSS,which was employed to calculate the output power and the energy distribution of the spent beam,was integrated with the Genetic algorithm.The detailed design of a Ku-band helix traveling wave was described and maximum collector efficiency of 89% with electronic efficiency of 26.9% was achieved from the simulation results.
Enhancing Broadband Helix TWT Performance Using Hollow Electron Beam

Shilong Zhu,Yulu Hu,Luanfeng Gao,Xiaofang Zhu,Quan Hu,Xiaobin Wang,Jianling Cui,Li Xu,Bin Li

DOI: https://doi.org/10.1109/tps.2024.3409372

IF: 1.368

2024-01-01

IEEE Transactions on Plasma Science

Abstract:This article presents a study on the utilization of annular beams in broadband helix traveling wave tubes (HTWTs). The research delves into the beam-wave interaction (BWI) performance of HTWTs under different hollow electron beam conditions. The theoretical analysis includes the use of gain parameter C and space charge parameter QC to evaluate the performance within the linear interaction region. Based on the analysis, a 4-20 GHz ultra-wideband traveling wave tube (TWT) based on a hollow beam scheme was designed using the software microwave tube simulator suite (MTSS). The design process involved optimizing the slow wave structure (SWS), the BWI performance, the electron gun, and the magnetic system. An output power greater than 109 W is achieved, and the small signal gain is better than 23 dB across the entire operating bandwidth. The particle-in-cell (PIC) solver in CST was used to verify the saturated gain of the designed TWT.
Application of Helix Pitch Step and Magnetic Field Amplitude Step and Period Step in Ka Band Traveling-Wave Tube

Chen Shan,Yue Lingna,Jin Lei,Zhao Guoqing,Wei Yanyu,Wang Wenxiang,Gong Yubin

DOI: https://doi.org/10.11884/hplpb201830.180050

2018-01-01

Abstract:The interaction simulation of the fan-shaped metal-dielectric support rod helix traveling wave tube(TWT) is carried out. On the basis of simple uniform pitch design, the helix pitch step and magnetic field step are used to improve the output power and electronic efficiency of the TWT in the working frequency band, and the problem of electron beam defocusing is solved. The final design results show that, when the working voltage is 9 kV and the working current is 210 mA, the gain of the traveling wave tube in the whole frequency band of 24-40 GHz is between 37.7 dB and 48.7 dB, the electronic efficiency is between 15.18% and 19.42%, and the output power is greater than 286 W. Comparing with the results of the original design, the growth rate increases by more than 4.19% on the electron efficiency, the growth rate of output power is more than 4.3%, especially in the range of 26-37 GHz, the growth rate of electron efficiency increases by more than 11.8%, and the growth rate of output power goes up to 11.9%. The design results are helpful to design improved fan-shaped metal-dielectric support rod for high efficiency broadband millimeter wave helix TWT.
Simulation of Cross-Modulation and Inter-Modulation of 2.5D Multi-Frequency Large Signal in Helix Traveling Wave Tube

Baoliang Hao,Kangsong Tang,Liu Xiao,Shi Li,Mingguang Huang,Pukun Liu

DOI: https://doi.org/10.3969/j.issn.1672-7126.2011.01.06

2011-01-01

Abstract:A semi-analytical, semi-particle, 2.5-dimension, multi-frequency interaction model was developed to numerically simulate the cross-modulation and inter-modulation of the large signal of the traveling wave tube (TWT), operating in a multi-frequency mode. In the simulation, the operating frequencies were assumed to be integer multiples of a base frequency, i. e., the lowest frequency; and the space charge field distributions were evaluated by solving the discrete Helmholtz equations, assisted by the modified particle-in-cell method. The simulated results in the two-tone simulation agree fairly well with the experimental results involving the inter-modulation, and the 3rd and 5th cross-modulation of an L-band TWT.
Design of a Q-Band High Efficiency Helix TWT

Wei Li,Lingna Yue,Jin Xu,Hairong Yin,Jinchi Cai,Guoqing Zhao,Wenxiang Wang,Yanyu Wei,Jun He,Zhiqiang Zhang

DOI: https://doi.org/10.1109/ivec56627.2023.10157126

2023-01-01

Abstract:A Q-band high efficiency helix traveling wave tube (TWT) is designed and simulated in this paper. By using appropriate slow wave structure and taking reasonable helix pitch tapering method, high electronic efficiency and output power can be obtained. The 3D electromagnetic simulation software CST is used for the calculation of the high frequency characteristics and beam-wave interaction. The preliminary simulation results show that no oscillation is observed in the output signal. The electronic efficiency of this helix TWT exceeds 25.8% within the frequency range of 37-42.5GHz, the output power is more than 220W, and the gain is greater than 51dB.
Helix Slow-wave Structure with Changed Pitches for a Q-band Traveling-wave Tube

Pu Zhang,Silong Huang,Zhifang Lyu,Shengkun Jiang,Xin Wang,Huarong Gong,Yubin Gong,Zhaoyun Duan

DOI: https://doi.org/10.1109/irmmw-thz50926.2021.9567465

2021-01-01

Abstract:In this paper, a helix slow-wave structure (SWS) with changed pitches for a Q-band traveling-wave tube (TWT) is proposed. Changed pitches are used to achieve more sufficient beam-wave interaction in the SWS. The high frequency characteristics and beam-wave interaction of the Q-band TWT are analyzed by using CST. The voltage standing wave ratio is less than 1.5 from 39 to 42 GHz. The simulation results of the beam-wave interaction show that the Q-band TWT with the changed pitches can generate output power of more than 80 W and electronic efficiency of 14% in the operating frequency band. The electronic efficiency reaches the maximum of 16.09% at 39 GHz.
Optimization Design of Helix Pitch for Efficiency Enhancement in the Helix Travelling Wave Tubes

Duan Zhao-Yun,Gong Yu-Bin,Lue Ming-Yi,Wei Yan-Yu,Wang Wen-Xiang

DOI: https://doi.org/10.1088/0256-307x/25/3/035

2008-01-01

Chinese Physics Letters

Abstract:The output section of a helix travelling wave tube usually contains a helix pitch taper for high rf electron efficiency. By keeping the rf field as synchronous as possible with the decelerating electron beam bunches, the rf field can extract much more energy from the beam, and thus the maximum electron efficiency can be realized. Recently, a global simulated annealing algorithm has been employed to design the helix pitch profile so as to improve the electron efficiency as much as possible. From the numerical results, it is concluded that the electron efficiency can be enhanced by about 4%-8%.
Design of Slow-Wave Structure and Beam-Wave Interaction Simulation for Helix Traveling-Wave Tube

Yao Ruoyan,Tang Tao,Zhao Guoqing,Huang Minzhi,Gong Yubin

DOI: https://doi.org/10.11884/hplpb201426.063030

2014-01-01

High Power Laser and Particle Beams

Abstract:A Ku-band helix traveling-wave tube (TWT) is designed using theoretical analysis and simulation. The effect of the variation in inner radius on dispersion and coupled impedance is analyzed to optimize the slow-wave structure of helix TWT. The input and output structure of TWT is simulated, the input reflecting coefficient is less than -19 dB and the voltage standing wave ratio (VSWR) is less than 1.24. Periodic permanent-magnetic field is used as electromagnetic focusing system, the magnetic system period is 8.5 mm and the magnetic peak value is 0.17 T. The slow-wave circuit with property of dynamic velocity tapper (DVT) is used to increase the interaction efficiency, it can provide enough time for the interaction of beam and high-frequency field and make electrons continuously transport energy to high-frequency field. The helix TWT is simulated using a three-dimensional particle-in-cell (PIC) code. The simulation results demonstrate that the output power is bigger than 88.7 W, the electron efficiency is bigger than 14.8% and the saturated gain is bigger than 34.6 dB in the frequency range from 12.5 to 16.0 GHz.
The Small Signal Theory Analysis and Optimization Design of High Efficiency Broadband TWTs

Hong-xia Yi,Liu Xiao,Pu-Kun Liu

DOI: https://doi.org/10.1109/ivesc.2010.5644393

2010-01-01

Abstract:Broadband helix traveling wave tube (TWT), because of its wide bandwidth and high gain, has potential applications in electronic countermeasure (ECM) systems and space exploration. It's a challenge to obtain high efficiency TWT over a multi-octave band, since its fundamental efficiency is degraded and harmonic power content is enhanced at lower band frequencies and the efficiency at high frequencies deteriorates because of insufficient interaction impedance and large distributing loss. The fundamental method of the design of an ultra-broadband TWT usually uses two-section output circuit: the first output section using unloaded circuit is to make the growing wave gain occur only at lower end of the band; the second output section using a loaded helix circuit is designed to be in synchronism with the RF wave at all frequency. In this paper, this fundamental method was analyzed using Pierce small signal theory, and then the special helix pitch profile using only negative dispersion slow wave structure (SWS) was shaped to satisfy the design request. The helix pitch profile was optimized to obtain a higher electronic efficiency using genetic algorithm at high frequency (18GHz).
Analysis of Electromagnetic Performance of Helix TWT with Beam Loaded

Xiaofang Zhu,Yulu Hu,Quan Hu,Bin Li

DOI: https://doi.org/10.1109/ivec.2018.8391674

2018-01-01

Abstract:To make more accurate analysis of electromagnetic performance of Helix Traveling Wave Tube (HTWT), the beam- loading effect is considered by treating the electron beam as an anisotropic medium focusing with an infinite magnetic field. Using this method, together with the sheath-helix model, the dispersion, coupling impedance and characteristic impedance of HTWT are obtained and compared with those from cold-test simulation. The results show that the electron beam will affect the EM performance of HTWT to some extent, and considering the effect is helpful when designing high-performance TWTs.
A modified slotted helix slow-wave structure for high-power millimeter-wave TWT

Luwei Liu,Yanyu Wei,Hairong Yin,Jin Xu,Guoqing Zhao,Yubin Gong

DOI: https://doi.org/10.1109/IVEC.2013.6571013

2013-01-01

Abstract:A modified slotted helix slow-wave structure is proposed to develop high-power, wide-bandwidth millimeter TWT. The electromagnetic characteristics are calculated by HFSS. The results show that the modified structure has higher interaction impedance and lower attenuation compared with original slotted helix SWS, which would lead to higher output power in millimeterwave TWT.
Theoretical Determination of TWT Helix Loss

Zhaoyun Duan,Yubin Gong,Wenxiang Wang,Yanyu Wei

DOI: https://doi.org/10.1109/ivelec.2007.4283393

2007-01-01

Abstract:A general theory has been developed to account for the effect of the dielectric loss of discrete dielectric rods on traveling wave tube helix loss. It is clearly shown that the influence of dielectric loss on attenuation constant is much larger at the millimeter frequency band than that at the microwave frequency band. The general theory developed here has been further conformed by comparing the results with those obtained elsewhere for some special cases.
Thermal Analysis of a Ka-band Helix TWT with Semi-metallic Rod

Shengzhe Lv,Lingna Yue,Ziqing Bai,Chiyi Liu,Wenxiang Wang,Yanyu Wei,Jin Xu,Hairong Yin,Guoqing Zhao

DOI: https://doi.org/10.1109/irmmw-thz50926.2021.9567531

2020-01-01

Abstract:The high frequency characteristics and beam wave interaction characteristics of a Ka-band (26-40GHz) helix traveling wave tube (TWT) with rectangular semi-metallic rod are presented. The design results show that the TWT has the gain of more than 42dB, the output power of more than 220W and the electronic efficiency of more than 19% in the working bandwidth. Now the high frequency structure of the TWT are manufactured, the preparation for the transmission test is in progress.

The Study of AM/PM Coefficient in Helix TWT

The Study of Group Delay Distortion in Helix TWT

Research of Efficiency Enhancement in a Helix TWT with Simulated Annealing Algorithm

P2-36: Simulation of crossmodulation and intermodulation products of helix TWT using a new 2.5D multifrequency large signal code

Influence of Attenuator on the Performance of the Helix TWTs

Numerical Optimization of Pitch Profile Foroverall Efficiency Enhancement of a Space TWT

Study the Mechanism and Suppression of AM/PM Conversion of Traveling-Wave Tubes Using Eulerian Hydrodynamic Analysis

An Improved Optimization Method for Helix Pitch Profile in Twts

Efficiency Enhancement of Space TWT based on Collectability

Enhancing Broadband Helix TWT Performance Using Hollow Electron Beam

Application of Helix Pitch Step and Magnetic Field Amplitude Step and Period Step in Ka Band Traveling-Wave Tube

Simulation of Cross-Modulation and Inter-Modulation of 2.5D Multi-Frequency Large Signal in Helix Traveling Wave Tube

Design of a Q-Band High Efficiency Helix TWT

Helix Slow-wave Structure with Changed Pitches for a Q-band Traveling-wave Tube

Optimization Design of Helix Pitch for Efficiency Enhancement in the Helix Travelling Wave Tubes

Design of Slow-Wave Structure and Beam-Wave Interaction Simulation for Helix Traveling-Wave Tube

The Small Signal Theory Analysis and Optimization Design of High Efficiency Broadband TWTs

Analysis of Electromagnetic Performance of Helix TWT with Beam Loaded

A modified slotted helix slow-wave structure for high-power millimeter-wave TWT

Theoretical Determination of TWT Helix Loss

Thermal Analysis of a Ka-band Helix TWT with Semi-metallic Rod