PROGRESS WORK ON A CW DEUTERON RFQ WITH MAGNETIC COUPLING WINDOWS *
Qi Fu,Weiping Dou,Matthew Easton,Pingping Gan,Shu Gao,Yuan He,Haipeng Li,Yuanrong Lu,Qiuyun Tan,Zhi Wang,K. Zhu
DOI: https://doi.org/10.18429/jacow-ipac2018-tupal050
2018-01-01
Abstract:A new 162.5 MHz RFQ has been built for a joint 973 project between Peking University (PKU) and Institute of Modern Physics (IMP). It is designed to deliver 50-mA deuteron beams to 1 MeV in CW mode, with an intervoltage of 60 kV and a length of 1.809 m. Due to its window-type structure, the RFQ has compact cross-section, sufficient mode separation and high specific shunt impedance. It consists of two segments fabricated and installed at IMP. The assembling error of the cavity is less than 0.05 mm. The RF measurements show good electrical properties of the resonant cavity with a measured unloaded quality factor equal to 96.4% of the simulated value. After tuning, we obtained the nominal frequency and field unbalance within ±1.0%. Preparation of high-power test of this RFQ is underway. This paper will cover the fabrication details and RF measurements, as well as the progress of high-power test. INTRODUCTION High-current continuous-wave (CW) RFQ is greatly needed for basic research, energy, medicine, etc., but also a great challenge. Since 2013, PKU and IMP have been collaborating on a new 973 project, which aims to build a 50-mA CW deuteron RFQ. The design of beam dynamics and RF structure has been completed [1-2]. Main parameters of this RFQ are listed in Table 1. As shown in Fig. 1, the RFQ adopts a window-type structure [3-4], with low power consumption and sufficient mode separation, with no stabilizing rods required. At present, the RFQ has been fabricated, assembled and tested at IMP. Table 1: Main Parameters of the Window-Type RFQ Parameter Value Operating frequency [MHz] 162.5 Particle D+ Beam current [mA] 50 Duty factor 100% Input/output energy [MeV] 0.05/1.01 Average radius [mm] 3.88 Vane tip radius [mm] 2.57~3.32 Inter-vane voltage [kV] 60 Length of the vanes [m] 1.809 Cavity radius [mm] 170.00 Mode separation between TE210 and TE110 [MHz] 3.144 Power loss [kW] 46.532 Peak power density [kW/m2] 3.846×105 Quality factor 9300 Shunt impedance [kΩ·m] 139.982 Figure 1: 3D model of the window-type RFQ. FABRICATION The RFQ cavity consists of two nearly identical segments of 904.50-mm length and input/output flanges, which are all made of oxygen-free copper (OFC). Each segment is divided into four vanes and four cavity walls for manufacturing. The RFQ is also equipped with 28 60mm-diameter tuners, 2 couplers, 8 vacuum ports, 8 pickups and 56 cooling connectors. The fabrication procedure passed the following steps: 1. All the components went through the rough machining, deep-hole processing, semi-finishing and fine machining in turn. Ball-end milling tools were used during processing the vane modulations, as the transvers radius of the vane tip was designed to change along the RFQ. As shown in Fig. 2, the maximal machining error was measured to be 0.0317 mm, located at the vane tip. 2. The RFQ components were vertically assembled together. After properly adjusting the vanes, the assembling errors were measured to be within 0.05 mm at both ends of each segment. ___________________________________________ * Work supported by NSFC, Grand No. 2014CB845503 † Corresponding author: zhukun@pku.edu.cn; yrlu@pku.edu.cn 9th International Particle Accelerator Conference IPAC2018, Vancouver, BC, Canada JACoW Publishing ISBN: 978-3-95450-184-7 doi:10.18429/JACoW-IPAC2018-TUPAL050 04 Hadron Accelerators A08 Linear Accelerators TUPAL05