Abstract:The purpose of this study is to experimentally and numerically investigate thermal and residual deformations of plastic ball grid array (PBGA) package and assembly. In the experiments, a full-field shadow moire with a sensitivity of 29.2 mum/fringe is used for measuring their real-time out-of- plane deformations (warpages) during heating and cooling conditions. The elastic moduli (Es) and coefficients of thermal expansion (CTEs) for epoxy molding compound (EMC) and organic substrate are measured in terms of temperatures by dynamic mechanical analyzer (DMA) and thermo-mechanical analyzer (TMA), respectively. And a finite element method with the input of these measured material properties is employed to numerically simulate the thermally-induced deformations of them, in order to understand the insight of mechanics. The full-field warpages of the PBGA package and assembly from shadow moire were documented during the temperature cycling (from room temperature to 220degC). It is interesting that the maximum warpages with concave shape for both the package and assembly occur at near 155degC during this thermal cycling, (rather than with convex shape at room temperature by assuming the warpage-free (or stress-free) temperature is at 175degC of molding). This issue has been resolved through the finite element analyses by cooperating with the residual strain (stress) in the EMC of the package, which is obtained by measuring the residual and thermal deformations of the detached EMC/die bi-material structure. This residual strain of the EMC maybe comes either from the chemical shrinkage of the EMC curing, or more possible stress relaxation of the EMC during the first solder reflow of attaching the solder balls. Furthermore, the thermal deformations for both the package and assembly were fully addressed by the finite element models. Both consistent results indicate that the more severe coplanarity with the value of about 275 mum at the corner of the substrate with the size of 40 times 40 times 1.7 mm occurs at near 155degC, due to the Tg and residual strains of the EMC, rather than at the room temperature. This severe coplanarity can be mitigated by lowering the residual shrinkage strain. And the warpage of the PBGA assembly coincides with the package at the temperature beyond 155degC (highly resulting from apparent creep of the solder balls), but is larger than that of the package below 155degC, due to constraint of the PCB through less-pronounced creep solder balls.

Finite Element Analysis and Optimization for PBGA Package

Modeling and Optimization of Moisture Diffusion and Integrated Thermo-Hygro-Vapor Stress for PBGA Package

Finite element analysis of 2.5D packaging processes based on multi-physics field coupling for predicting the reliability of IC components

Comparison between Experimental Measurement and Numerical Analysis of Warpage in PBGA Package and Assembly with the Consideration of Residual Strain in the Molding Compound

Investigation On Fbga Block Warpage By Finite Element Simulation

Analysis of warpage and reliability of very thin profile fine pitch ball grid array

Wafer Warpage Optimization Via Finite Element Analysis for a 3D Chiplet Package

Modeling of Underfilled PBGA Assemblies Using Both Viscoelastic and Elastic Material Properties

Comparison of Mechanical Modeling to Warpage Estimation of RDL-First Fan-Out Panel-Level Packaging

Deep Reinforcement Learning-Based Pin Map Optimization of BGA Package for EMC

Investigation on Block Warpage of FBGA Package

Thermal Stress Analysis of PBGA Using a Fluid-Solid Coupling Method under Steady Convective Heat Transfer

Finite Element Analysis on Dry Baking of Plastic IC Components

Theoretical and Experimental Investigation of Warpage Evolution of Flip Chip Package on Packaging during Fabrication

Modeling of board-level package by Finite Element Analysis and laser interferometer measurements

Moisture Desorption and Hygro-Vapor-Thermal Induced Interfacial Delamination in Underfilled FCBGA Package During Reflow Process

Study on the Manufacturability of XDFOI Package with Organic RDLs (XDFOI-O)

Numerical analysis on MUF process for flip chip packaging

Optimization Method for Hot Air Reflow Soldering Process Based on Robust Design

Finite Element Analysis of Underfill Effect on the CBGA Package Reliability under Thermal Cycling

A Numerical Technique to Evaluate Warpage Behavior of Double Sided Rigid-Flex Board Assemblies during Reflow Soldering Process