Abstract:High Performance Polymers, Ahead of Print. Polyimide aerogel, presenting an outstanding new material for lightweight protective thermal insulation, has garnered significant attention in the aerospace field. Despite its potential, due to the high production cost of the supercritical drying method used for its preparation, its widespread application is limited. In this research, a series of lightweight polyimide aerogels (F-PIAs, 3,3',4,4'-biphenyl tetracarboxylic dianhydride (s-BPDA) and 4,4'-diaminodiphenyl ether (ODA)) with excellent thermal protection properties were prepared by lyophilization. The findings indicated that F-PIAs (Freeze-dried polyimide aerogels) exhibited comparable physical characteristics to S-PIAs (Supercritical-dried polyimide aerogels), while their preparation cost was even more economical. F-PIAs exhibits excellent flexible and compression behavior (compression strength up to 1.16 MPa, modulus up to 12.8 MPa), which provide a great structural basis for the production of molded thermal insulation protective materials. The average pore diameter of F-PIAs is in the range of 7∼11 nm. The nanoporous structure leads to the gas within the pores of the aerogel producing the Knudsen effect, thereby significantly enhancing the thermal insulation performance of the aerogel. The thermal conductivity of F-PIA-4 (Freeze-dried polyimide aerogels with a solid content of 4%) at room temperature is as low as 0.023 W·m−1·K−1, which is superior to the PIAs (0.043 W·m−1·K−1) prepared by lyophilization in literature. Its thermal diffusion coefficient changes from 0.108 mm2·s−1 to 0.18 mm2·s−1 in the temperature range of 27°C to 200°C, demonstrating good thermal insulation performance at high temperatures. Meanwhile, after heating on a 150°C flat plate for 11 min and 41 s, the surface temperature of F-PIA-4 was only 36.2°C, further verifying its excellent thermal insulation performance. The results of the TGA experiment on F-PIA-4 demonstrated the high-temperature stability of aerogel (Td5% is higher than 523°C, Td10% is higher than 566°C). The exceptional properties of F-PIAs hold significant practical reference value in helping to reduce the manufacturing cost of high-performance aerogel thermal insulation materials, thereby enabling their widespread application in aerospace, military, and civil field.

Ultralight and Low Thermal Conductivity Polyimide–Polyhedral Oligomeric Silsesquioxanes Aerogels

Polyimide Aerogels Crosslinked Through Cyclic Ladder‐like and Cage Polyamine Functionalized Polysilsesquioxanes

Ultralight and heat-insulating mesoporous polyimide aerogels cross-linked with aminated SiO2 nanoparticles

Mechanically strong, thermal-insulated, and ultralow dielectric polyimide aerogels with adjustable crosslinking methods

Cross-Linked Polyimide Aerogels with Excellent Thermal and Mechanical Properties

Polyimide aerogels with low thermal conductivity and high-temperature stable properties prepared by lyophilization for flexible thermal protection

Synthesis and Characterization of Rigid and Thermostable Polyimide Aerogel Crosslinked with Tri(3-Aminophenyl)phosphine Oxide

Lightweight, Strong, and Super-Thermal Insulating Polyimide Composite Aerogels under High Temperature

Preparation and Characterization of Polyimide Aerogels with a Uniform Nanoporous Framework

Moisture‐Resistant and Mechanically Strong Polyimide‐Polymethylsilsesquioxane Hybrid Aerogels with Tunable Microstructure

Fabrication and Characterization of a High-Strength Polyimide/Thermoplastic Polyurethane Composite Aerogel with Hydrophobicity and Low Thermal Conductivity

Mechanically robust poly(urethane-imide) aerogels with excellent thermal insulation and sound absorption by ambient drying

High-mechanical-strength polyimide aerogels crosslinked with 4, 4′-oxydianiline-functionalized carbon nanotubes

Ultralow shrinkage polyimide hybrid aerogel composite enhanced with organic fibers for thermal protection

Effect of polymer concentration and cross-linking density on the microstructure and properties of polyimide aerogels

Mechanically Strong and Thermally Stable Chemical Cross-Linked Polyimide Aerogels for Thermal Insulator

Mechanically strong polyimide aerogels cross-linked with low-cost polymers

Low Shrinkage Polyimide Aerogel Cross-Linked with Amino-Functionalized Hollow Glass Microbeads for Thermal and Acoustic Insulation

Synthesis of Micro/nano Multi-Scale Polyimide Aerogels Via Confinement-Controlled Freeze-Casting

Polyimide-Coating-on-Aramid Nanofiber Strategy Toward Ultralight Organic Aerogels with Multifunctional Properties

Fire-resistant Polyimide-Silica Aerogel Composite Aerogels with Low Shrinkage, Low Density and High Hydrophobicity for Aerospace Applications