Abstract:Membrane biofouling represents a major challenge ever-present in the practical application of polyamide (PA) thin-film composite (TFC) reverse osmosis (RO) membranes. This work focused on grafting polyacrylamide (PAAm) onto PA-TFC via an in-situ atomic transfer radical polymerization (ATRP) method to improve the biofouling resistance of PA-TFC. The ATRP initiators, isobutyryl bromide (iPB), were introduced into PA matrix using a bifunctional small molecule, 2-bromoisobutyryl bromide (BIBB), added in organic hexane solutions to participate in interfacial polymerization through the condensation reaction with m-phenylenediamine. The successful introduction of iPB was confirmed by membrane surface characterizations, and the iPB density in PA layer was tuned by varying the BIBB concentrations in hexane solutions based on the variation in water permeance and salt rejections of iPB-loaded PA-TFC. The ATRP for the gradual growth of PAAm brush was thus in-situ achieved on the PA-TFC surface from the pre-incorporated iPB groups and the length of PAAm chains was facilely controlled via tuning ATRP polymerization time. The PAAm grafted PA-TFC exhibited a minimum decrement of water permeance and essentially retained salt rejections relative to the un-grafted ones. More importantly, the grafted membranes presented synergistically enhanced anti-adhesion and bacteriostatic performance towards either Gram-negative Escherichia coli (E. coli) or Gram-positive Bacillus subtilis (B. subtilis). Also, the grafted membranes presented a lower final flux decline ratio (FDRf) and higher final flux recovery ratio (FRRf) in relation with the un-grafted membranes in the dynamic bovine serum albumin (BSA) fouling test. Particularly, the membrane grafted with longer PAAm chains from extended grafting time showed better anti-biofouling performance: the sterilization ratio towards E. coli and B. subtilis achieved up to 98.8% and 99.0%, respectively, and FDRf of just 3.7% and FRRf of 97.6% after 3 × 8 h BSA fouling test for the membrane subjected to 2 h ATRP grafting. The PAAm grafting induced greater water wettability of membrane surface and the flexible chain structure of PAAm were proposed to account for the enhanced anti-adhesion and bacteriostasis towards bacteria, which collaboratively led to the improved biofouling resistance.

PAN ultrafiltration membranes grafted with natural amino acids for improving antifouling property

High-flux, Anti-Fouling Dendrimer Grafted PAN Membrane: Fabrication, Performance and Mechanisms

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Antifouling Ultrafiltration Membranes Made from PAN-b-PEG Copolymers: Effect of Copolymer Composition and PEG Chain Length

Preparation of a Low-Protein-Fouling and High-Protein-Retention Membrane via Novel Pre-Hydrolysis Treatment of Polyacrylonitrile (PAN)

Preparation and Characterization of an Amphiphilic Polyamide Nanofiltration Membrane with Improved Antifouling Properties by Two-Step Surface Modification Method

Surface Glycosylation of Polyacrylonitrile Ultrafiltration Membrane to Improve Its Anti-Fouling Performance

Preparation of PES ultrafiltration membranes with natural amino acids based zwitterionic antifouling surfaces

Polyaniline/polysulfone ultrafiltration membranes with improved permeability and anti-fouling behavior

Improved protein fouling resistance of PVDF membrane grafted with the polyampholyte layers

Preparation of Polyacrylonitrile Ultrafiltration Membranes

Micro-nanostructure Tuning of PEEK Porous Membrane Surface Based on PANI In-Situ Growth for Antifouling Ultrafiltration Membranes

Antifouling and Self-Cleaning Performances of the Porous Polypropylene Membrane Surface Grafted by P(NIPAAm-PEGMA)

Improving the biofouling resistance of polyamide thin-film composite membrane via grafting polyacrylamide brush on the surface by in-situ atomic transfer radical polymerization

Polyacrylonitrile-based block copolymer ultrafiltration membranes with enhanced antifouling and pollutants removal efficiency

Mineralized Polyacrylonitrile-Based Ultrafiltration Membranes with Improved Water Flux and Rejection Towards Dye

Acrylonitrile-Based Copolymer Membranes Containing Reactive Groups: Surface Modification By The Immobilization Of Poly(Ethylene Glycol) For Improving Antifouling Property And Biocompatibility

PVDF ultrafiltration membrane with enhanced mechanical and filtration performance by hydrophilic pH-response nanofibers modification

A new method for tailoring the surface pore size and internal pore structure of ultrafiltration membranes without using additives—Atomization-assisted nonsolvent induced phase separation method

Enhancing the Hydrophilic and Antifouling Properties of Polypropylene Nonwoven Fabric Membranes by the Grafting of Poly(n-Vinyl-2-pyrrolidone) Via the ATRP Method

Surface Modification of Poly(acrylonitrile-Co-maleic Acid) Membranes by the Immobilization of Poly(ethylene Glycol)