Abstract:There is an increasing demand for the development of a new kind of secondary battery with high capacity and long cycle life. The sulfur cathode with the theoretical capacity of 1672 mAh/g (sulfur) has attracted researchers' attention.1 However, the Li-S batteries faces huge challenges because of the capacity fading caused by the polysulfide's shuttle effect and the safety issues caused by the lithium metal. Recently, researchers were attracted on the fabrication of metallic lithium free battery with the lithiated sulfur cathode.2 However, due to the high sensitivity of lithium sulfide (Li2S) to the moisture of air, this method have to be taken completely in an inert atmosphere, which raises the manufacturing cost and obstruct the access to commercialization. Consequently, it is urgent to introduce a new way to fabricate the lithiated sulphur cathode to meet the application requirement. Herein, we prepared Li2S/KB cathode by an in situ synthesis method under the protection of ion-selective polypyrrole (PPy) layer. The anion doped PPy layer was deposited by electrodeposition method on S/KB cathode.3 The layer by layer structure of the cathode was proved by SEM analysis of the cross-section image (showed in Figure 1a). A lithium source was used to contact with the cathode in a wet environment and the lithium ions will go to the cathode by diffusion. The product of pre-lithiation was confirmed to be amorphous Li2S by XPS and XRD analysis. As Figure 1b shows, the first charge capacity can reach 1153 mAh/g (sulfur) at 0.1C rate after paired with a Li foil anode. This Li2S/KB cathode can be coupled with lithium free anode, such as graphite, Si to form a lithium free battery. Figure 1. (a) Cross section FE-SEM image of the S/KB/PPy cathode. Inset is the FE-SEM image of the PPy layer of the S/KB/PPy cathode. (b) The charge and discharge of the pre-lithiated cathode at a charge rate of 0.1C. Furthermore, the thickness of PPy was proved to influence the cyclability and capacity of the coin type cell. With the help of PPy, the shuttle effect will be alleviated by the ion-selective property of the PPy layer. Additionally, the lithiated S/KB cathode can be exposed to air for a short time because of the protection of PPy layer. We believe these properties of the lithiated S/KB cathode will provide possibility to assemble Li2S battery in air atmosphere and pave way to commercialization. Acknowledgement This work is supported by Advanced Low Carbon Technology Research and Development Program (JST-ALCA) Special Priority Research Area "Next-generation Rechargeable Battery”. References 1. Manthiram, A.; Fu, Y.; Chung, S. H.; Zu, C.; Su, Y. S. Chem. Rev., 114, 11751-87 (2014). 2. Son, Y.; Lee, J.-S.; Son, Y.; Jang, J.-H.; Cho, J. Adv. Energy Mater., 5, 1500110 (2015). 3. Nakamura, N.; Yokoshima, T.; Nara, H.; Momma, T.; Osaka, T. J. Power. Sources, 274, 1263-1266 (2015). Figure 1

On-site Chemical Pre-Lithiation of S Cathode at Room Temperature on a 3D Nano-Structured Current Collector

Li+ Solvation Structure Modification in Chemical Prelithiation Enabling Spatially Homogeneous Sei Toward High Performance Siox Anode

Preparation of Pre-Lithiated Sulfur Cathode by an in Situ Contacting Reaction

A Pre-Lithiation Method for Sulfur Cathode Used for Future Lithium Metal Free Full Battery

Inverse Fabrication of Li 2 S‐Nanocrystals@Doped‐Carbon Loaded on Woven Carbon Fibers to Spatial Structure Cathodes for High‐Stable Lithium–Sulfur Batteries

Synthesis of Lithium Sulfide (li2s) Wrapped Carbon Nano Composite for Binder-Free Li2S Cathode

In Situ Polymerization of Nanostructured Conductive Polymer on 3D Sulfur/Carbon Nanofiber Composite Network as Cathode for High‐Performance Lithium–Sulfur Batteries

Cathode Nanostructuring and Separator Modification for High-Performance Lithium-Sulfur Batteries

In-situ Anchoring Sulfiphilic Silica Nanoparticles Onto Macro-Mesoporous Carbon Framework for Cost-Effective Li-S Cathodes

Nanofiber-based electrode current collector for high-energy Li-S batteries towards practical application for energy storage

Bio-inspired Nanoscaled Electronic/Ionic Conduction Networks for Room-Temperature All-Solid-State Sodium-Sulfur Battery

Battery Prelithiation Enabled by Lithium Fixation on Cathode

In situ preparation of chromium carbide–modified carbon nanofibers as functional electrocatalyst for polysulfide reduction in lithium/sulfur batteries

Facile Synthesis of Lithium Sulfide Nanocrystals for Use in Advanced Rechargeable Batteries.

Chemical Prelithiation/Presodiation Strategies Toward Controllable and Scalable Synthesis of Microsized Nanoporous Tin at Room Temperature for High‐Energy Sodium‐Ion Batteries

A mechanochemical synthesis of submicron-sized Li2S and a mesoporous Li2S/C hybrid for high performance lithium/sulfur battery cathodes

Chemical Immobilization and Conversion of Active Polysulfides Directly by Copper Current Collector: A New Approach to Enabling Stable Room‐Temperature Li‐S and Na‐S Batteries

Integrated Design of Interlayer/Current-Collector: Heteronanowires Decorated Carbon Microtube Fabric for High-Loading and Lean-Electrolyte Lithium-Sulfur Batteries

Li2S@C/CNT Composite Cathode with Botryoidal Conductive Network for Advanced Lithium–sulfur Batteries

(Digital Presentation) Ex Situ Electrochemical Pre-Lithiation of Silicon for Lithium-Ion Battery Anodes

Long-Life, High-Efficiency Lithium–Sulfur Battery from a Nanoassembled Cathode