Abstract:Functional gradient high-strength steel structures on the basis of a novel tailored spray quenching process can achieve an excellent crashworthiness and weight reduction, which own a promising future in advanced automotive and mechanical engineering. This paper focuses on the temperature distributions and mechanical properties characteristics of high strength 22MnB5 steel under complex spray jetting conditions. A spray density-based physical modeling method is simplified to describe the spray flow field and the water film evolution on the hot 22MnB5 surface during the spray quenching process. Fluid characteristics of spray jetting with single/twin nozzles and corresponding heat transfer intensity are systematically investigated by self-developed experimental scenarios. The results reveal that the fluid-solid heat transfer coefficient (IHTC) is dependent on the spray-quenching temperature distribution, which owns an intense correlation between post-quenched mechanical property and the jetting parameters involving the spray jetting pressure (SJP), the spray jetting height (SJH), the nozzle distance (ND), and initial quenching temperature (IQT). The average cooling rate under the single/twin nozzles jetting conditions can reached as 28.5–170.5 °C/s and 36.84–137.42 °C/s, corresponding to the peak IHTCs are 10.11–49.47 kW/(m2 K) and 9.69–44.76 kW/(m2 K), respectively. The hardness firstly increases and then decreases from the central point/zone to the edge along the radial direction after the spray quenching process. The largest radial hardness after the single/double nozzles spray quenching can be up to 50.21 % and 31.58 % larger than the lowest value, respectively. Moreover, the in-plane temperature field and corresponding post-quenched mechanical properties are further numerically predicted by introducing into the time-dependent IHTC and coupling with the CFD and Johnson-Mehl-Avrami (JMA) modeling. Finally, a validation work of U-type specimen was conducted to show the spray quenching technology owns a prospective future for gaining more complex-shaped parts with tailored mechanical properties.

Novel Boron Microalloyed Steel Used for High-power Wind Turbine Yaw Bearing Rings and Corresponding Simulation of Heat Treatment Process

Application of 40CrNiMoV steel to heavy section bearing

Hot Deformation Behavior and Numerical Simulation of 40CrNiMo Steel for Wind Turbine Pulley Shafts

Control of mechanical properties of a high-entropy alloy Cantor CoCrFeMnNi

Hot Deformation Behavior and Microstructure Evolution of 2Cr12Ni4Mo3VNbN Steel Used for Last‐Stage Large Blades of Steam Turbine

Process Optimization and Performance of New TBM Disc Cutter Ring Steel

Study on Hot‐Compressive Deformation Behavior and Microstructure Evolution of 12Cr10Co3MoWVNbNB Martensitic Steel

Stress Response Behavior, Microstructure Evolution and Constitutive Modeling of 22MnB5 Boron Steel under Isothermal Tensile Load

Experimental microstructure evolution and cutting simulation for dynamic mechanical behaviors of 18CrNiMo7-6 steel considering heat treatment conditions

Experimental Investigations On Mechanical Properties Of A High Cr Ferritic Steel For Usc Steam Turbine Rotor

Experimental and numerical investigation on temperature field and tailored mechanical properties distribution of 22MnB5 steel in spray quenching process

Research on the micro zone strength and strain hardening behavior in the 30Cr2Ni4MoV rotor welded joint

Effect of forging sequence and heat treatment on microstructure of high-duty power-plant shaft made of Cr-Mo ultra-high strength steel

Heat Treatment Properties of 42CrMo Steel for Bearing Ring of Varisized Shield Tunneling Machine

Mechanical properties of 30Cr2Ni4MoV low-pressure rotor steel with different microstructures

Cyclic Softening Properties of 30cr2mov Steel at Elevated Temperatures

Influence of Deep Cryogenic Treatment and Secondary Tempering on Microstructure and Mechanical Properties of Medium-Carbon Low-Alloy Steels

Effect of Heat Treatment on Structure and Properties of B Alloyed High Speed Steel for Rolling Mill Rolls

Microstructures and Properties of a Novel Carburizing Nanobainitic Bearing Steel

Microstructure and Mechanical Properties of 22mnb5 Steel with Different Heat Treatment