Abstract:Mussel-inspired polydopamine (PDA) can serve as building blocks and interfaces in designing functional materials. Here, the use of PDA as an interlayer between polyaniline (PANi) and multidimensional carbon materials, such as graphene quantum dots (GQD), multiwalled carbon nanotubes (MWCNT), and graphene nanosheets (GNS), to improve the thermoelectric performance of p-type polymer-based materials has been reported. The introduction of PDA promotes the carrier mobility of GQD/PDA/PANi, CNT/PDA/PANi, and GNS/PDA/PANi ternary composites due to the superior adhesive property of PDA. An optimal conductivity of 4.98 × 104 S m–1 and a power factor of 92.17 μW m–1 K–2 at 363 K are achieved in GNS/PDA/PANi, which are much higher than the values of GNS/PDA and GNS/PANi. More surprisingly, despite the fact that GQD/PDA, CNT/PDA, and GNS/PDA binary composites show p-type properties, the pyrolysis treatment of GQD/PDA, CNT/PDA, and GNS/PDA at 800 °C results in a gain in both the electrical conductivity and negative Seebeck coefficient of c-GQD/PDA, c-CNT/PDA, and c-GNS/PDA. The c-CNT/PDA composites possess the highest Seebeck value of −30.2 μV K–1 and a maximum power factor value of 35.57 μW m–1 K–2. Finally, a flexible thermoelectric generator with 24 thermoelectric units composed of GNS/PDA/PANi and c-CNT/PDA is demonstrated, which gives an output voltage of 52.8 mV at a temperature difference of 60 °C.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c01457?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c01457</a>.Thermal conductivity measurements and TE characterization; electrical conductivity and Seebeck coefficient of all the samples at 303, 333, and 363 K; TE properties of pristine GQD, CNT, and GNS at 363 K; FTIR spectra, XPS spectra, TEM images, and size distributions of GQD; appearance of GNS dispersion solution and GNS/PDA dispersion solution in water after ultrasonication; carrier mobility and carrier concentration of PANi-based composites at 363 K; PF and thermal conductivity of PDA and PDA-based composite materials at 363 K; PF and thermal conductivity of PANi-based binary composites at 363 K; digital photos of n-type composite films of bending 150 and 180° and after bending 180°; cross-sectional SEM images of n-type composite films of bending 180° and magnification times; digital photos showing bending of p-type composite films by 150 and 180° and after bending to 180°; cross-sectional SEM images showing the bending of p-type composite films by 180° and magnification times; and schematic diagram of the device configuration and the working principle of TEG (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c01457/suppl_file/am1c01457_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Fabricate Organic Thermoelectric Modules Use Modified PCBM and PEDOT:PSS Materials

A simple thermoelectric device based on inorganic/organic composite thin film for energy harvesting

N-type Core-Shell Heterostructured Bi2S3@Bi Nanorods/polyaniline Hybrids for Stretchable Thermoelectric Generator

Transparent flexible thin-film p–n junction thermoelectric module

Design and Fabrication of Wearable Thermoelectric Generator Device for Heat Harvesting

Fabrication and evaluation of microscale thermoelectric modules of Bi<sub>2</sub>Te<sub>3</sub>-based alloys

A hierarchical design for thermoelectric hybrid materials: Bi2Te3 particles covered by partial Au skins enhance thermoelectric performance in sticky thermoelectric materials

Flexible Bi2Te3/PEDOT nanowire sandwich-like films towards high-performance wearable cross-plane thermoelectric generator and temperature sensor array

Polymer/carbon Nanotube Composite Materials for Flexible Thermoelectric Power Generator

Fabrication and Performance Simulation of Microscale Thermoelectric Modules Made with Bi2Te3-Based Alloys

Fabrication And Evaluation Of Microscale Thermoelectric Modules Of Bi2te3-Based Alloys

Vertically Designed High-Performance and Flexible Thermoelectric Generator Based on Optimized PEDOT:PSS/SWCNTs Composite Films

PEDOT-based Thermoelectrics

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

Enhancement in thermoelectric properties using a P-type and N-type thin-film device structure

Novel Hybrid p- and n-Type Organic Thermoelectric Materials Based on Mussel-Inspired Polydopamine

PEDOT:PSS and Ni-based thermoelectric generator for solar thermal energy conversion

Poly(3,4-ethylenedioxythiophene) (PEDOT) as promising thermoelectric materials and devices

PEDOT-based thermoelectric composites: Preparation, mechanism and applications

Solution processed organic thermoelectrics: towards flexible thermoelectric modules

Recent Progress in Thermoelectric Materials Based on Conjugated Polymers