Abstract:Although <math>{101¯2}</math> twinning behavior has been extensively studied, it has rarely been investigated under biaxial tension. In the present research, the mechanical response and <math>{101¯2}</math> twinning behavior of a Mg AZ31 sheet under biaxial tension with various stress ratios (<math>σND:σTD</math>) along the normal direction (ND) and transverse direction (TD) were systematically studied. The results indicate that the yield stress along the ND is nearly independent of <math>σND:σTD</math>. Schmid law applied to <math>{101¯2}</math> twinning under biaxial tension yields better efficiency than that for uniaxial tension, and a higher efficiency is observed with a larger stress ratio along the TD; the fraction of experimentally observed twin variants with Schmid factors (SFs) of ranks 1 and 2 is approximately 45% for uniaxial tension, whereas it is approximately 68% for <math>σND:σTD=2:1</math> and approximately 88% for <math>σND:σTD=1:2</math>. This result contradicts with the previously reported result that Schmid law is more efficient for uniaxial stress states than under multiaxial stress conditions. It is found that biaxial tension will increase the difference in SF for the six twin variants and make Schmid law more efficient. Twin variant selection and volume fraction are highly dependent on <math>σND:σTD</math>. For uniaxial tension, the activities for the six variants are similar, and the (0002) poles of the twins are distributed evenly on a circle approximately 80°–90° away from the ND. In contrast, the variants <math>(01¯12)[011¯1]</math> and <math>(011¯2)[01¯11]</math> are more favorable under biaxial tension, and more (0002) poles of the twins concentrate around the rolling direction with a higher ratio of <math>σTD</math>. At a similar strain level, the twin fraction under biaxial tension is often different from that under uniaxial tension, and this difference varies with <math>σND:σTD</math>. This mechanism is associated with a stress-ratio-mediated detwinning behavior under biaxial tension. The findings in the present study provide a new and significant understanding of the twinning behavior of Mg alloys.

Variant selection of {10-12}-{10-12} double twins during the tensile deformation of an AZ31 Mg alloy

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

{ 10 1 ̄ 2 } twinning behavior under biaxial tension of Mg–3Al–1Zn plate

Variant selection of primary–secondary extension twin pairs in magnesium: An analytical calculation study

Microstructure Evolution and Selection Behavior of Twin Variants of Mg-5Gd-3Y-0.5Zr Alloy during Secondary Deformation

Towards Understanding {10-11}-{10-12} Secondary Twinning Behaviors in AZ31 Magnesium Alloy during Fatigue Deformation

Extension Twin Variant Selection During Uniaxial Compression of A Magnesium Alloy

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

Influence of initial {10−12} twins on twinning behavior of extruded AZ31 alloys during free-end torsion

Identification and Analysis of Twinning Variants During Compression of a Mg–Al–Zn Alloy

{332}<113> and {112}<111> Twin Variant Activation during Cold-Rolling of a Ti-Nb-Zr-Ta-Sn-Fe Alloy

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Towards understanding double extension twinning behaviors in magnesium alloy during uniaxial tension deformation

Twin variant selection criteria in magnesium alloy: a review

Introducing transformation twins in titanium alloys: an evolution of α-variants during additive manufacturing

Correlation between imposed deformation and transformation lattice strain on α variant selection in a metastable β-Ti alloy under isothermal compression

A Study of {10-12} Twinning Activity Associated with Stress State in Mg-3Al-1Zn Alloy during Compression

Dynamic recrystallization, twinning behaviors and mechanical response of pre-twinned AZ31 Mg alloy sheet along various strain paths at warm temperature

A novel method for predicting variant selection of {1 0 1 ̄ 2} twins in pure hafnium

Generation of fine extension twins in rolled magnesium alloy AZ31B at room temperature by simple shear