Abstract:<p>High borated steel sheets containing 0.25 wt% to 4.0 wt% boron including hypoeutectic (0.28 wt% B and 2.11 wt% B), eutectic (2.43 wt% B) and hypereutectic (4.01 wt% B) compositions were tried to be fabricated by a novel strip casting technology, and the effects of boron content on sub-rapid solidification behavior and subsequent microstructural evolution together with mechanical properties was studied. It was found that the morphology of borides depended greatly on the boron content. When increasing boron, the morphological change of borides was network-like → grainy → cluster-like → plate-like. Various orientation relationships between different morphological borides and γ-Fe in as-cast steels were also identified. After subsequent hot-rolling and solution-treating, ultra-fine (<10 μm) borides were obtained in hypoeutectic and eutectic steels. Benefiting from that, excellent mechanical properties was achieved, which was much better than that of steels prepared by traditional ingot casting. Particularly, when the boron content approached eutectic composition, of which the effect on the microstructure and mechanical properties was more sensitive. The steels containing 2.11 wt% and 2.43 wt% boron exhibited different morphological borides with a total elongation of 14.1% and 8.0%, respectively. Moreover, a thin hypereutectic borated steel sheet was also prepared, but the borides were very large and the total elongation was very low. The correlation between microstructure and strength was clarified based on the Hall-Petch behavior and intermetallic strengthening effect. Smaller γ-grains and higher volume fraction of borides were responsible for higher strength. The plastic behavior of steels was influenced by strain-hardening rate that was determined by the volume fraction of γ-Fe matrix. A better sustainable strain-hardening capability was beneficial to extend the stage of uniform deformation and enhance the ductility. In addition, the mechanical properties of steels were also decided by the fracture mechanism that was dominated by the size of borides.</p>

Effect of Boron on Bainitic Transformation Kinetics after Ausforming in Low Carbon Steels

Effect of Ausforming Temperature and Strain on the Bainitic Transformation Kinetics of A Low Carbon Boron Steel

Isothermal Transformation, Microstructure and Mechanical Properties of Ausformed Low-Carbon Carbide-Free Bainitic Steel

Effect of Boron on the Solidification Characteristics and Constitutive Equation of S31254 Superaustenitic Stainless Steel

The combining effects of ausforming and below-Ms or above-Ms austempering on the transformation kinetics, microstructure and mechanical properties of low-carbon bainitic steel

Effects of ausforming temperature on bainite transformation kinetics, microstructures and mechanical properties in ultra-fine bainitic steel

Effect of Ausforming on the Bainitic Transformation and Microstructure in Medium Carbon V–N Micro-Alloyed Steel

Effects of Ausforming on Isothermal Bainite Transformation Behaviour and Microstructural Refinement in Medium-Carbon Si–Al-rich Alloy Steel

Tailoring Bainitic Transformation and Enhancing Mechanical Properties of Carbide-Free Bainitic Steel Via High-Temperature Ausforming

Effect of Boron on Continuous Cooling Transformation Behavior of 460B Steel

Bainite Transformation-Kinetics-Microstructure Characterization of Austempered 4140 Steel

Effect of two-step ausforming on bainite transformation and retained austenite in a medium-carbon bainitic steel

Effect of Trace Element B on the Microstructure and Mechanical Properties of 8Cr4Mo4V Bearing Steel

Effect of boron addition on the GB precipitation and SRC resistance of CGHAZ in advanced bainitic heat-resistant steel

Effect of high‐temperature deformation on bainite transformation of a low‐carbon bainite steel

Effect of Boron on Microstructures and Low-Temperature Impact Toughness of Medium-Carbon CrMo Alloy Steels with Different Quenching Temperatures

Effect of Boron Content on Microstructure and Mechanical Properties of As-Cast High-Boron Middle-Carbon Alloy Steels

Carbide-Free Bainite in Medium Carbon Steel

The effect of austenite deformation on bainite formation in an alloyed eutectoid steel

Effects of boron content on the microstructure and mechanical properties of twin-roll strip casting borated steel sheets

Research on bainite transformation in steels