Abstract:Multispectral thermometry is based on the law of blackbody radiation and is widely used in engineering practice today. Temperature values can be inferred from radiation intensity and multiple sets of wavelengths. Multispectral thermometry eliminates the requirements for single-spectral and spectral similarity, which are associated with two-colour thermometry. In the process of multispectral temperature inversion, the solution of spectral emissivity and multispectral data processing can be seen as the keys to accurate thermometry. At present, spectral emissivity is most commonly estimated using assumption models. When an assumption model closely matches an actual situation, the inversion of the temperature and the accuracy of spectral emissivity are both very high; however, when the two are not closely matched, the inversion result is very different from the actual situation. Assumption models of spectral emissivity exhibit drawbacks when used for thermometry of a complex material, or any material whose properties dynamically change during a combustion process. To address the above problems, in the present study, we developed a multispectral thermometry method based on optimisation ideas. This method involves analysing connections between measured temperatures of each channel in a multispectral temperature inversion process; it also makes use of correlations between multispectral signals at different temperatures. In short, we established a multivariate temperature difference correlation function based on the principles of multispectral radiometric thermometry, using information correlations between data for each channel in a temperature inversion process. We then established a high-precision thermometry model by optimising the correlation function and correcting any measurement errors. This method simplifies the modelling process so that it becomes an optimisation problem of the temperature difference function. This also removes the need to assume the relationships between spectral emissivity and other physical quantities, simplifying the process of multispectral thermometry. Finally, this involves correction of the spectral data so that any impact of measurement error on the thermometry is reduced. In order to verify the feasibility and reliability of the method, a simple eight-channel multispectral thermometry device was used for experimental validation, in which the temperature emitted from a blackbody furnace was identified as the standard value. In addition, spectral data from the 468–603 nm band were calibrated within a temperature range of 1923.15–2273.15 K, resulting in multispectral thermometry based on optimisation principles with an error rate of around 0.3% and a temperature calculation time of less than 3 s. The achieved level of inversion accuracy was better than that obtained using either a secondary measurement method (SMM) or a neural network method, and the calculation speed achieved was considerably faster than that obtained using the SMM method.

Modelling Temperature-Induced Spectral Variations in Chemical Process Monitoring

Broadening the Scope of Food Quality Control: a Calibration Transfer Strategy for Minimizing External Influences on Spectral Analysis

An Efficient Temperature Calibration Method Based on the Improved Infrared Forward Model and Bayesian Inference

Analysis of Multi-Factor on Measurement Improvement of an Infrared Imager in Low-Temperature Environments

Correction of temperature-induced spectral variation by continuous piecewise direct standardization

The Application of Piecewise Direct Standardization with Snv in Calibration Transfer of Raman Spectra

Maintaining the Predictive Abilities of Tea Moisture Content Models on Different Environment Based on Visible and Near-Infrared Spectroscopy Technique

Influence Of Temperature On Visible And Near-Infrared Spectra And The Predictive Ability Of Multivariate Models

[A Simple and Convenient Standardization Algorithm of NIR Spectra].

Optimizing Meta-Parameters in Continuous Piecewise Direct Standardization

Two-Level Independent Component Regression Model for Multivariate Spectroscopic Calibration

Temperature Correction of Spectra to Improve Solute Concentration Monitoring by In Situ Ultraviolet and Mid-Infrared Spectrometries toward Isothermal Local Model Performance

Study on the Influence of Temperature on Near Infrared Spectra

Standardization of complex biologically derived spectrochemical datasets

Systematic prediction error correction: A novel strategy for maintaining the predictive abilities of multivariate calibration models

A Soft Calibration Technique for Infrared Imaging Based on Physical Model of Thermal Radiation and Variational Bayesian Inference from Small Dataset

A local pre-processing method for near-infrared spectra, combined with spectral segmentation and standard normal variate transformation

Iterative Interval Backward Selection Algorithm and Its Application in Calibration Transfer of Near Infrared Spectra

Multispectral Thermometry Method Based on Optimisation Ideas

A robust calibration modeling strategy for analysis of interference-subject spectral data

Correcting Temperature Dependence in Miniature Spectrometers Used in Cold Polar Environments