Abstract:Abstract Objective To study the biomechanical characteristics of each tissue structure when using different 3D printing Cage in osteoporotic patients undergoing interbody fusion. Methods A finite element model of the lumbar spine was reconstructed and validated with regarding a range of motion and intervertebral disc pressure from previous in vitro studies. Cage and pedicle screws were implanted and part of the lamina, spinous process, and facet joints were removed in the L4/5 segment of the validated mode to simulate interbody fusion. A 280 N follower load and 7.5 N·m moment were applied to different postoperative models and intact osteoporotic model to simulate lumbar motion. The biomechanical characteristics of different models were evaluated by calculating and analyzing the range of motion of the fixed and cephalic adjacent segment, the stress of the screw-rod system, the stress at the interface between cage and L5 endplate, and intervertebral disc pressure of the adjacent segment. Results After rigid fixation, the range of motion of the fixed segment of model A-C decreased significantly, which was much smaller than that of the osteoporotic model. And with the increase of the axial area of the interbody fusion cages, the fixed segment of model A-C tended to be more stable. The range of motion and intradiscal pressure of the spinal models with different interbody fusion cages were higher than those of the complete osteoporosis model, but there was no significant difference between the postoperative models. On the other hand, the L5 upper endplate stress and screw-rod system stress of model A-C show a decreasing trend in different directions of motion. The stress of the endplate is the highest during flexion, which can reach 40.5 MPa (model A). The difference in endplate stress between models A-C was the largest during lateral bending. The endplate stress of models A and B was 150.5% and 140.9% of that of model C, respectively. The stress of the screw-rod system was the highest during lateral bending (model A, 102.0 MPa), which was 108.4%, 102.4%, 110.4%, 114.2% of model B and 158.5%, 110.1%, 115.8%, 125.4% of model C in flexion, extension, lateral bending, and rotation, respectively. Conclusions For people with osteoporosis, no matter what type of cage is used, good immediate stability can be achieved after surgery. Larger cage sizes provide better fixation without significantly increasing ROM and IDP in adjacent segments, which may contribute to the development of ASD. In addition, larger cage sizes can disperse endplate stress and reduce stress concentration, which is of positive significance in preventing cage subsidence after operation. The cage and screw rod system establish a stress conduction pathway on the spine, and a larger cage greatly enhances the stress-bearing capacity of the front column, which can better distribute the stress of the posterior spine structure and the stress borne by the posterior screw rod system, reduce the stress concentration phenomenon of the nail rod system, and avoid exceeding the yield strength of the material, resulting in the risk of future instrument failure.

The Dosimetric Impacts of Vertebral Implants (pedicle Screw And/or Bone Cement) on Spinal Cord

Dose Evaluation of Fractionated Schema and Distance from Tumor to Spinal Cord for Spinal Sbrt with Simultaneous Integrated Boost: A Preliminary Study

Effect of percutaneous kyphoplasty bone cement injection on biomechanics of adjacent lumbar spine in animal models with osteoporosis

Biomechanical Effects of Bone Cement Volume on the Endplates of Augmented Vertebral Body: a Three-Dimensional Finite Element Analysis.

Dosimetric Factors Of Stereotactic Body Radiation Therapy For Isolated Spinal Metastatic Diseases: Impact Of Distance From Tumor Target To Spinal Cord On Planning Dosimetry And Low Dose Spillage Restriction

Effects of pedicle screw cement augmentation on spine tumor surgery

The use of carbon fiber/polyetheretherketone (CF/PEEK) in pedicle screw fixation for spinal neoplasms-potential advantages in postoperative imaging and radiotherapy planning

Pedicle screw insertion with patient-specific 3D-printed guides based on low-dose CT scan is more accurate than free-hand technique in spine deformity patients: a prospective, randomized clinical trial

Application of 3D O-arm-navigated Pedicle Screw Insertion in Spinal Stability Reconstruction in Patients with Spinal Cord and Spinal Column Tumors

The Accuracy and Effectiveness of Automatic Pedicle Screw Trajectory Planning Based on Computer Tomography Values: an in Vitro Osteoporosis Model Study.

Effect of different cone-beam CT image-guidance strategies on the accumulated dose of radiotherapy for spine metastases

A Biomechanical Study on Cortical Bone Trajectory Screw Fixation Augmented with Cement in Osteoporotic Spines.

Dose calculation and reporting with a linear Boltzman transport equation solver in vertebral SABR

Radiation dose reduction in thoracic and lumbar spine instrumentation using navigation based on an intraoperative cone beam CT imaging system: a prospective randomized clinical trial

Dosimetric Analysis of 3D-Printing Non-Coplanar Template Combined with CT-guided 125I Seed Implantation for the Treatment of Spinal Metastasis

Biomechanical Effects of Different Bone Cement Diffusion Patterns after Vertebroplasty:Finite Element Analysis

Finite element biomechanical analysis of 3D printed intervertebral fusion cage in osteoporotic population

Effect of Halo-Vest on dose distribution of radiotherapy for primary cervical spine malignant tumors

Pedicle screw path planning for multi‐level vertebral fixation

Impact of Cement Distribution on the Efficacy of Percutaneous Vertebral Augmentation for Osteoporotic Fractures

Three-dimensional Finite Element Analysis of Optimal Distribution Model of Vertebroplasty.