Abstract:Commercial application of Li–S batteries is greatly restricted by their unsatisfactory cycle retention and poor cycling life originating from the lithium polysulfide (LiPS) shuttling effect and sluggish sulfur redox kinetics. Various strategies have been proposed to boost the performances of Li–S batteries, including nanostructured sulfur composites, functional separators/interlayers, electrode/electrolyte additives, and so on. However, how to combine two or more strategies to efficiently settle these challenging issues confronted by Li–S batteries is in desperate need. Here, we demonstrate a powerful combined strategy of introducing novel 3D WS2/carbon nanotube (CNT) networks built by hybridization of 1D CNTs with 2D WS2 into Li–S batteries, simultaneously serving as a functional cathode additive and separator coating. Such 3D WS2/CNTs networks with abundant edge sites, a large active surface, and a fast electron pathway twice perform functions from the cathode side and separator surface: (1) to suppress polysulfide diffusion through a physical barrier and chemical interactions; (2) to accelerate LiPS conversion reactions; and (3) to enhance conductivity for better sulfur reactivation and high utilization. As a result, the as-built WS2/CNTs-incorporated battery configuration achieves a commendable combination of capacity, rate, and cycle stability (1491 mA h g–1 at 0.2 C, 754 mA h g–1 at 5 C, and initial capacity of 1069 mA h g–1 with an ultralow decay rate of 0.040% per cycle over 1000 cycles at 1 C) along with remarkably mitigated anode corrosion and low self-discharge.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c13193.TG plot for the Super-P/sulfur composite, SEM images of CNTs, XPS survey spectra of WS2/CNTs before and after Li2S6 adsorption, optimized WS2 (001) surface model and Li2S6 molecular structure, SEM images of PP and WS2/CNTs separators and digital images of the WS2/CNTs separator under bending/folding and after cycling, SEM image coupled with EDX mappings and TEM image of WS2/CNTs after cycling, polysulfide penetration test of PP, CNT, and WS2/CNTs separators, equivalent circuit models and EIS simulation results, CV and GCD profiles of four different battery configurations, and GCD profiles of the battery using WS2/CNTs as a cathode additive and separator coating at different scan rates, and electrochemical performance comparison of Li–S batteries based on different functional separators or cathode additives (PDF)This article has not yet been cited by other publications.

Sulfur Cathode Integrated with Multileveled Carbon Nanoflake-Nanosphere Networks for High-Performance Lithium-Sulfur Batteries

A 3D Conductive Network of Porous Carbon Nanoparticles Interconnected with Carbon Nanotubes As the Sulfur Host for Long Cycle Life Lithium-Sulfur Batteries.

Constructing Monolithic Sulfur Cathodes with Multifunctional N,P Dual-Doped Carbon Nanocages to Achieve High-Areal-capacity Lithium-Sulfur Batteries

Reconstruction of Multidimensional Carbon Hosts with Combined 0D, 1D and 2D Networks for Enhanced Lithium-Sulfur Batteries

Built‐in Carbon Nanotube Network Inside a Biomass‐Derived Hierarchically Porous Carbon to Enhance the Performance of the Sulfur Cathode in a Li‐S Battery

Three-dimensional Spongy Framework As Superlyophilic, Strongly Absorbing, and Electrocatalytic Polysulfide Reservoir Layer for High-Rate and Long-Cycling Lithium-Sulfur Batteries

Robust Electrical “highway” Network for High Mass Loading Sulfur Cathode

Sulfur Nanocrystals Confined in Carbon Nanotube Network As A Binder-Free Electrode for High-Performance Lithium Sulfur Batteries

Multifunction Co-Nx species to manipulate polysulfides conversion kinetics toward highly efficient lithium-sulfur batteries

Confining Sulfur in Integrated Composite Scaffold with Highly Porous Carbon Fibers/Vanadium Nitride Arrays for High‐Performance Lithium–Sulfur Batteries

Engineering the Conductive Network of Metal Oxide‐Based Sulfur Cathode toward Efficient and Longevous Lithium–Sulfur Batteries

Integration of nickel phosphide nanodot-enriched 3D graphene-like carbon with carbon fibers as self-supported sulfur hosts for advanced lithium sulfur batteries

Constructing 1D/2D Interwoven Carbonous Matrix to Enable High-Efficiency Sulfur Immobilization in Li-S Battery

Promoting the Synergistic Effect of Sulfur Immobilization and Polysulfides Trapping by Nitrogen Functionalized Interconnected Hollow Carbon Nanocages for High-Performance Lithium–sulfur Batteries

Inverse Fabrication of Li 2 S‐Nanocrystals@Doped‐Carbon Loaded on Woven Carbon Fibers to Spatial Structure Cathodes for High‐Stable Lithium–Sulfur Batteries

Multifunctional Co3s4@Sulfur Nanotubes for Enhanced Lithium-Sulfur Battery Performance

3D Tungsten Disulfide/Carbon Nanotube Networks as Separator Coatings and Cathode Additives for Stable and Fast Lithium–Sulfur Batteries

In Situ Assembly of MnO2 Nanosheets on Sulfur-Embedded Multichannel Carbon Nanofiber Composites As Cathodes for Lithium-Sulfur Batteries

Self-Templated Formation of Interlaced Carbon Nanotubes Threaded Hollow Co3S4 Nanoboxes for High-Rate and Heat-Resistant Lithium-Sulfur Batteries.

3D Hyperbranched Hollow Carbon Nanorod Encapsulated Sulfur Composites for Lithium-Sulfur Batteries with Superior Electrochemical Performance

Three-Dimensional Functionalized Carbon Nanotubes/Graphitic Carbon Nitride Hybrid Composite as the Sulfur Host for High-Performance Lithium–Sulfur Batteries