Abstract:The use of superhydrophobic surfaces in a broad range of applications is receiving a great deal of attention due to their numerous functionalities. However, fabricating these surfaces using low-cost raw materials through green and fluorine-free routes has been a bottleneck in their industrial deployment. This work presents a facile and environmentally friendly strategy to prepare mechanically robust superhydrophobic surfaces with engineered lotus leaf mimetic multiscale hierarchical structures via a hybrid route combining soft imprinting and spin-coating. Direct soft-imprinting lithography onto starch/polyhydroxyurethane/cellulose nanocrystal (SPC) films formed micro-scaled features resembling the pillar architecture of lotus leaf. Spin-coating was then used to assemble a thin layer of low-surface-energy poly(dimethylsiloxane) (PDMS) over these microstructures. Silica nanoparticles (SNPs) were grafted with vinyltriethoxysilane (VTES) to form functional silica nanoparticles (V-SNPs) and subsequently used for the fabrication of superhydrophobic coatings. A further modification of PDMS@SPC film with V-SNPs enabled the interlocking of V-SNPs microparticles within the cross-linked PDMS network. The simultaneous introduction of hierarchical microscale surface topography, the low surface tension of the PDMS layer, and the nanoscale roughness induced by V-SNPs contributed to the fabrication of a superhydrophobic interface with a water contact angle (WCA) of ∼150° and a sliding angle (SA) of <10°. The PDMS/V-SNP@SPC films showed an ∼52% reduction in water vapor transmission rate compared to that of uncoated films. These results indicated that the coating served as an excellent moisture barrier and imparted good hydrophobicity to the film substrate. The coated film surfaces were able to withstand extensive knife scratches, finger-rubbing, jet-water impact, a sandpaper-abrasion test for 20 cycles, and a tape-peeling test for ∼10 repetitions without losing superhydrophobicity, suggesting superior mechanical durability. Self-cleaning behavior was also demonstrated when the surfaces were cleared of artificial dust and various food liquids. The green and innovative approach presented in the current study can potentially serve as an attractive new tool for the development of robust superhydrophobic surfaces without adverse environmental consequences.

Development of Copper Phosphate Nanoflowers on Soy Protein toward a Superhydrophobic and Self-Cleaning Film

Super-hydrophobic and Self-cleaning PVDF Film Fabricated by Chemical Bath Deposition

Abrasion‐Resistant, Hot Water‐Repellent and Self‐Cleaning Superhydrophobic Surfaces Fabricated by Electrophoresis of Nanoparticles in Electrodeposited Sol–Gel Films

Facile Fabrication of Superhydrophobic Nanocomposite Coatings Based on Water‐Based Emulsion Latex

A Superhydrophobic and Self-Cleaning Photoluminescent Protein Film with High Weatherability

Facile Fabrication of Fluorine-Free, Transparent and Self-Cleaning Superhydrophobic Coatings Based on Biopolymer Castor Oil

Bioinspired spiderweb-liked protective hydrophobic layer for improving the durability of superhydrophilic/air superoleophobic coatings

An Eco-Friendly One-Step Method to Fabricate Superhydrophobic Nanoparticles with Hierarchical Architectures

Preparation and Characterization of Stable Superhydrophobic Copper Foams Suitable for Treatment of Oily Wastewater

Superhydrophobic Cu2s@ Cu2o Film on Copper Surface Fabricated by A Facile Chemical Bath Deposition Method and Its Application in Oil-Water Separation

Superhydrophobic Polysilsesquioxane Nanospike/Glass Microfiber Composite for Separation of Oil-Water Mixtures

Facile Fabrication of a Durable Ni3S2 Nanorod Arrays Superhydrophobic Surface with Self-Cleaning and Degradation Properties

Superhydrophobic materials with good oil/water separation and self-cleaning property

Robust and Eco-Friendly Superhydrophobic Starch Nanohybrid Materials with Engineered Lotus Leaf Mimetic Multiscale Hierarchical Structures

Facile Preparation of Superhydrophobic Surfaces Based on Metal Oxide Nanoparticles

A robust bilayer nanofilm fabricated on copper foam for oil–water separation with improved performances

Surface Modification with Hierarchical Cuo Arrays Toward A Flexible, Durable Superhydrophobic and Self-Cleaning Material

Facile Fabrication Of Superhydrophobic Cu(Oh)(2) Nanorod And Cuo Nanosheet Arrays On Copper Surface

A Facile Method for the Fabrication of a Superhydrophobic Polydopamine-Coated Copper Foam for Oil/water Separation

Facile Preparation of Superhydrophobic Nano-Aluminum/copper(ii) Oxide Composite Films with Their Exposure and Heat-Release Stability

Production and characterization of stable superhydrophobic surfaces based on copper hydroxide nanoneedles mimicking the legs of water striders.