Abstract:Lithium-sulfur (Li-S) batteries are widely regarded as the next-generation energy storage technology, due to their high potential in energy density and a low projected cost. Practical applications of such batteries are plagued with radical challenges that mainly stem from two factors. First, both sulfur and its final lithiation product, Li2S, are insulating. Thus, the reaction kinetics is slow and often leads to a low attainable capacity. Second, active material dissolve in the electrolyte in the form of lithium polysulfides. This dissolution causes a series of problems, including loss of cathode materials by diffusion away from the cathode, collapse of the cathode structure, and the polysulfide shuttle effect. As a result, Li-S batteries commonly show fast capacity decay and low coulombic efficiency. Herein, we report the exceptional battery performance of porous carbon-sulfur composite microspheres, PSC-S, that benefited from simultaneous control of nanostructure and microscale particle morphology. The porous carbon microspheres (PSC) was synthesized as the sulfur host,by combining emulsion polymerization and evaporation-induced self-assembly (EISA) process, with a good control of both pore structure and microscale particle morphology. Such material not only demonstrated superioty in attainable capacity, but also in several other critical parameters for the development of high-energy Li-S batteries. PSC-S composite boasts a high tap density of 1.08 g/ml and contains 75 wt.% sulfur embedded into the mesopores of its carbon framework. At a high sulfur loading of 5 mg-S/cm2 and 60wt.% sulfur content in the electrode, this material delivers both high gravimetric and high volumetric capacity with excellent retention. Carbon nanotubes (CNTs) can also be readily incorporated into the microspherical structure in the synthesis process to form a porous spherical carbon-carbon nanotube-sulfur composite (PSC-CNT-S). CNT incorporation effectively raises the conductivity of the composite, and thus significantly improves its high-rate performance. At a high current density of 2.8 mA/cm2, an initial capacity of 1100 mAh/g and a reversible capacity of 700 mAh/g after 200 cycles were achieved in PSC-CNT-S. The resultant areal capacity of over 3.5 mAh/cm2 is much higher than in previous reports of Li-S cathodes fabricated using coating techniques.

Wrinkled Sulfur@graphene Microspheres with High Sulfur Loading As Superior-Capacity Cathode for LiS Batteries

Advanced Sulfur Cathode Enabled by Highly Crumpled Nitrogen-Doped Graphene Sheets for High-Energy-Density Lithium-Sulfur Batteries

Graphene/MXene fibers-enveloped sulfur cathodes for high-performance Li-S batteries

High Sulfur Loading Composite Wrapped By 3d Nitrogen-Doped Graphene As A Cathode Material For Lithium-Sulfur Batteries

3D Dual-Confined Sulfur Encapsulated in Porous Carbon Nanosheets and Wrapped with Graphene Aerogels As A Cathode for Advanced Lithium Sulfur Batteries

Sulfur Synchronously Electrodeposited Onto Exfoliated Graphene Sheets As A Cathode Material For Advanced Lithium-Sulfur Batteries

Self-assembled N-graphene nanohollows enabling ultrahigh energy density cathode for Li-S batteries

Liquid-phase Exfoliated-Graphene-supporting Nanostructural Sulfur As High-Performance Lithium–sulfur Batteries Cathode

Graphene-Li2S-Carbon Nanocomposite for Lithium-Sulfur Batteries

Interfacial Engineering and Coupling of MXene/Reduced Graphene Oxide/C3N4 Aerogel with Optimized d‐Band Center as a Free‐Standing Sulfur Carrier for High‐Performance Li‐S Batteries

Nitrogen Doped Carbon Nanosheets Encapsulated in Situ Generated Sulfur Enable High Capacity and Superior Rate Cathode for Li-S Batteries

Sulfur-infiltrated porous carbon microspheres with controllable multi-modal pore size distribution for high energy lithium–sulfur batteries

Uniform Polypyrrole Layer-Coated Sulfur/Graphene Aerogel Via the Vapor-Phase Deposition Technique As the Cathode Material for Li-S Batteries

Three-dimensional Graphene Framework with Ultra-High Sulfur Content for a Robust Lithium–sulfur Battery

Three-Dimensional Sulfur/Graphene Multifunctional Hybrid Sponges for Lithium-Sulfur Batteries with Large Areal Mass Loading

Dual‐Confined Flexible Sulfur Cathodes Encapsulated in Nitrogen‐Doped Double‐Shelled Hollow Carbon Spheres and Wrapped with Graphene for Li–S Batteries

Nanoarchitectured Graphene/CNT@Porous Carbon with Extraordinary Electrical Conductivity and Interconnected Micro/Mesopores for Lithium‐Sulfur Batteries

Horizontally Aligned Lamellar Porous Graphene/nickel Composite for High Volumetric Capacity Lithium-Sulfur Batteries

Graphene-like G-C3n4 Nanosheets/sulfur As Cathode for Lithium–sulfur Battery

Mesoporous Carbon-Sulfur Composite Microspheres with Multiscale Morphology Control to Achieve High Areal Capacity for Lithium-Sulfur Battery Cathodes

Mesoporous N-doped graphene prepared by a soft-template method with high performance in Li-S batteries.