Abstract:Electromyography (EMG) is a valuable diagnostic tool for detecting neuromuscular abnormalities. Implantable epimysial electrodes are commonly used to measure EMG signals in preclinical models. Although classical resources exist describing the principles of epimysial electrode fabrication, there is a sparsity of illustrative information translating electrode theory to practice. To remedy this, we provide an updated, easy-to-follow guide on fabricating and testing a low-cost epimysial electrode. Electrodes were made by folding and inserting two platinum-iridium foils into a precut silicone base to form the contact surfaces. Next, coated stainless steel wires were welded to each contact surface to form the electrode leads. Lastly, a silicone mixture was used to seal the electrode. Ex vivo testing was conducted to compare our custom-fabricated electrode to an industry standard electrode in a saline bath, where high levels of signal agreement (sine [intraclass correlation - ICC= 0.993], square [ICC = 0.995], triangle [ICC = 0.958]), and temporal-synchrony (sine [r = 0.987], square [r = 0.990], triangle [r= 0.931]) were found across all waveforms. Low levels of electrode impedance were also quantified via electrochemical impedance spectroscopy. An in vivo performance assessment was also conducted where the vastus lateralis muscle of a rat was surgically instrumented with the custom-fabricated electrode and signaling was acquired during uphill and downhill walking. As expected, peak EMG activity was significantly lower during downhill walking (0.008 ± 0.005 mV) than uphill (0.031 ± 0.180 mV, p = 0.005), supporting the validity of the device. The reliability and biocompatibility of the device were also supported by consistent signaling during level walking at 14 days and 56 days post implantation (0.01 ± 0.007 mV, 0.012 ± 0.007 mV respectively; p > 0.05) and the absence of histological inflammation. Collectively, we provide an updated workflow for the fabrication and testing of low-cost epimysial electrodes.

A Stretchable Microneedle Electrode Array for Stimulating and Measuring Intramuscular Electromyographic Activity.

A low-cost, easy-fabricating stretchable microneedle-electrode array for intramuscular recording and stimulation

Characterization of A Stretchable Multielectrode Array for Epimysial Recording

Highly stretchable and customizable microneedle electrode arrays for intramuscular electromyography

A multi-scale electrode array (MSEA) to study excitation–contraction coupling of cardiomyocytes for high-throughput bioassays

Skin-integrated, biocompatible, and stretchable silicon microneedle electrode for long-term EMG monitoring in motion scenario

A PDMS-based integrated stretchable microelectrode array (isMEA) for neural and muscular surface interfacing.

Development and Evaluation of 3D‐Printed Dry Microneedle Electrodes for Surface Electromyography

Stretchable surface electromyography electrode array patch for tendon location and muscle injury prevention

High-density Stretchable Microelectrode Array Based on Multilayer Serpentine Interconnections

Towards Improving the Quality of Electrophysiological Signal Recordings by Using Microneedle Electrode Arrays

Highly Stretchable, Compliant, Polymeric Microelectrode Arrays for In Vivo Electrophysiological Interfacing

A Novel Exoskeleton Neuromuscular Interface Based on Motor Unit Action Potential Model Using High-Density Semg

Fabrication Of Flexible Microneedle Array Electrodes For Wearable Bio-Signal Recording

Using microneedle array electrodes for non-invasive electrophysiological signal acquisition and sensory feedback evoking

Development of a Low-cost Epimysial Electromyography Electrode: A Simplified Workflow for Fabrication and Testing

Muscle surface recording and stimulation using integrated PDMS-based microelectrode arrays: Recording-triggered stimulation for prosthetic purposes

Multichannel Microneedle Dry Electrode Patches for Minimally Invasive Transdermal Recording of Electrophysiological Signals

An Active Multielectrode Array for Collecting Surface Electromyogram Signals Using A-Igzo TFT Technology on Polyimide Substrate

Stretchable sEMG Electrodes Conformally Laminated on Skin for Continuous Electrophysiological Monitoring

A lithographically-patterned, elastic multi-electrode array for surface stimulation of the spinal cord