Abstract:An important task of the China Fusion Engineering Test Reactor physics design is to develop operation scenarios with high fusion power (1 GW), high bootstrap current fraction for steady-state and a plasma edge compatible with heat and particle exhaust. To achieve these goals, triangularity (δ) effects on the fusion performance of two candidate scenarios, with or without reversed magnetic shear (RS), namely conventional H-mode and RS H-mode, are evaluated using core-edge coupled integrated modeling in this paper. For fixed pedestal density, it is shown that higher δ is favorable for higher fusion performance in the conventional H-mode scenario while the fusion performance decreases with increasing δ in the RS H-mode scenario. In conventional H-mode, the higher fusion performance at high δ mainly comes from a higher pedestal temperature as predicted by EPED in combination with stiff core kinetic profiles. In the RS H-mode scenario with a local reversed shear region, the profiles are non-stiff and a strong internal transport barrier (ITB) exists at low δ. This results in higher density and temperature inside the ITB for low δ, leading to higher fusion power. If the pedestal temperature is kept fixed, in both scenarios the significant increase in pedestal density, which extends into the core, dominates at high δ and leads to much higher fusion power. For conventional H-mode, destabilization from increasing δ is partially balanced by stabilization due to increasing ν*. Since the normalized heat sources are quite similar, it results in minimal changes in the temperature profiles except for the lowest density case. For RS H-mode, destabilization from increasing δ is approximately balanced by stabilization due to increasing ν* in foot region, but a strong temperature ITB is still evident for low δ. The ability to take advantage of the high pedestal density in conventional H-mode and reversed shear scenario depends on its compatibility with edge density requirements from efficient heat and particle exhaust. Transport analysis is presented to elucidate the roles of δ, collisionality and magnetic shear in altering the profiles and the ITB, which contribute to the different behavior in the two scenarios.

Effect of Fuelling Depth on the Fusion Performance and Particle Confinement of a Fusion Reactor

Experimental study of injection depth and fuelling effects during supersonic molecular beam injection on the HL-2A tokamak

Burning Fraction, Radial Transport, and Steady State Profiles of Multi-Species Particles in CFETR Burning Plasmas

Estimation of China Fusion Engineering Test Reactor performance and burning fraction in different pellet fueling scenarios by a multi-species radial transport model

Estimation of CFETR performance and burning fraction in diﬀerent pellet fueling scenarios by a multi-species radial transport model

Modification of the fusion energy gain factor in magnetic confinement fusion due to plasma temperature anisotropy

Modeling and simulation of deposited energy gain via irradiation of heavy ion beams on the fusion reactor contains spherical fuel capsules with foam

Optimization of pellet design parameters to achieve deep fueling depth in EAST plasma with PAM code

Numerical study on the interface debonding effect on FCM fuel behavior

Influence of the Charge Exchange Reactions on Plasma Parameters in Magnetic Fusion Devices

Effects of the Mesostructures and Irradiation Conditions on the Thermo-Mechanical Coupling Behaviors in LWR-used Fully Ceramic-Microencapsulated Fuel Pellets

Simulation of the Alpha Particle Heating and the Helium Ash Source in an International Thermonuclear Experimental Reactor-like Tokamak with an Internal Transport Barrier

Energy deposition and deflection of α particles in hot dense plasmas relevant to inertial confinement fusions

Comparison analysis of 1D/2D/3D neutronics modeling for a fusion reactor

Effects of triangularity on the fusion performance of CFETR

Integral Analysis of the Effect of Material Dimension and Composition on Tokamak Neutronics

First principles and integrated modelling achievements towards trustful fusion power predictions for JET and ITER

How turbulence spreading improves power handling in quiescent high confinement fusion plasmas

Numerical Simulation Research on the Irradiation-Thermal-Mechanical Performance Evolution of FCM Fuel

Effects of the Key Parameters of TRISO Particle Buffer Layer on In-Pile Thermo-Mechanical Behavior in FCM Fuel Pellets

A study of the requirements of p-11B fusion reactor by tokamak system code