Abstract:Bimetallic catalysts are of great interest because they often display properties that differ from either of their parent metals. Previous studies on the Ni/Pt(111) bimetallic system have shown that the location of Ni atoms in the Pt(111) surface has a strong influence on the electronic and chemical properites of the surface [1]. The bimetallic surface consisting of a monolayer of Ni on top of bulk Pt(111), designated Ni-Pt-Pt(111), binds hydrogen and alkenes much more strongly than either parent metal, resulting in decreased hydrogenation activity. In contrast the surface consisting of a monolayer of Ni atoms in the subsurface region designated as Pt-Ni-Pt(111), has been shown to weaken metal-hydrogen bonds in comparison to Ni-Pt-Pt(111) or either parent metal surface. The resulting abundance of weakly bound hydrogen and alkenes on the Pt-Ni-Pt(111) surface increases its activity for novel low temperature hydrogenation pathways [2, 3]. In a previous attempt to extend these single crystal surface science studies to supported catalysts, PtCo bimetallic catalysts were found to be more active to hydrogenation reactions than PtNi bimetallic catalysts [4]. Therefore this study will focus on PtCo catalysts and the effect of different support materials on catalyst structure and activity. Co and Pt monometallic and PtCo bimetallic catalysts were synthesized and supported on γ-Al 2O 3, SiO 2, TiO 2, and activated carbon (AC). Temperature programmed reduction (TPR) studies were performed to characterize the reduction behavior of the catalysts and to identify suitable reduction conditions. CO chemisorption was used to determine the number of active sites on each catalyst. Flow reactor studies of benzene hydrogenation the series of catalysts were used to compare the activity of PtCo on the different supports. Normalizing the hydrogenation activity with the number of active sites yielded the following trend in activity: SiO 2 → Al 2O 3 → TiO 2 ∼ AC. Activation barriers were also calculated and followed a trend consistent with the normalized activity trend, that is: SiO 2 < Al 2O 3 < TiO 2 ∼ AC. Extended X-ray absorption fine structure (EXAFS) spectroscopy was used to characterize the extent of bimetallic formation. EXAFS analysis found that the SiO 2 and Al 2O 3 supported catalysts showed a greater extent of bimetallic formation (larger Pt-Co coordination number) than either the TiO 2 or AC supported catalysts. Both the TiO 2 and AC supported catalysts possessed large Pt-Pt coordination numbers, suggesting the presence of larger particles. Transmission electron microscopy (TEM) was utilized to characterize the particle sizes. Particles on the SiO 2 supported catalyst appeared to be the smallest and most dispersed, while larger particles were observed in both the TiO 2 and AC supported catalysts.

Effect of Oxide Supports on Pt-Ni Bimetallic Catalysts for the Selective Hydrogenation of Biomass-Derived 2(5H)-Furanone

Highly efficient Ni-Mn/SiO<sub>2</sub> catalyst for the selective hydrogenation of biomass-derived levulinic acid to -valerolactone under mild conditions

Atomic Layer Deposition of a Pt-Skin Catalyst for Base-Free Aerobic Oxidation of 5-Hydroxymethylfurfural to 2,5-Furandicarboxylic Acid

Selective Hydrogenation of Biomass-Derived 2(5H)-Furanone to Γ-Butyrolactone over Ni-Based Bimetallic Catalysts

Selective Hydrogenation of Furfural over Pt Based and Pd Based Bimetallic Catalysts Supported on Modified Multiwalled Carbon Nanotubes (MWNT)

Effect of Oxide Supports in Stabilizing Desirable Pt-Ni Bimetallic Structures for Hydrogenation and Reforming Reactions

Correlating C═C, C═O, and C═N Hydrogenation Activity with Hydrogen Binding Energies on Ni–Fe Bimetallic Catalysts

CO2‐assisted Controllable Synthesis of PdNi Nanoalloys for Highly Selective Hydrogenation of Biomass‐derived 5‐Hydroxymethylfurfural

The catalytic hydrogenation of furfural to 2-methylfuran over the Mg-Al oxides supported Co-Ni bimetallic catalysts

Selective hydrogenation of furfural and its derivative over bimetallic NiFe-based catalysts: Understanding the synergy between Ni sites and Ni–Fe alloy

Selective Hydrogenation of the Carbonyls in Furfural and 5-Hydroxymethylfurfural Catalyzed by PtNi Alloy Supported on SBA-15 in Aqueous Solution Under Mild Conditions

Highly Active and Selective NiFe/SiO2 Bimetallic Catalyst with Optimized Solvent Effect for the Liquid-Phase Hydrogenation of Furfural to Furfuryl Alcohol

Highly efficient and selective hydrogenation of furfural to furfuryl alcohol and cyclopentanone over Cu-Ni bimetallic Catalysts: The crucial role of CuNi alloys and Cu + species

Trimetallic NiZr/CoOx catalyst for the selective hydrogenation of furfural into furfuryl alcohol

Support effect on the low-temperature hydrogenation of benzene over PtCo bimetallic catalysts

Porous SiO 2 nanosphere-supported PtCuCo trimetallic nanoparticles for highly efficient and selective furfural hydrogenation

Enhanced CH 4 Selectivity in CO 2 Hydrogenation on Bimetallic Pt–Ni Catalysts with Pt Nanoparticles Modified by Isolated Ni Atoms

NiCu Nanoparticles for Catalytic Hydrogenation of Biomass-Derived Carbonyl Compounds

Bimetallic PtFe-Catalyzed Selective Hydrogenation of Furfural to Furfuryl Alcohol: Solvent Effect of Isopropanol and Hydrogen Activation

The Pt-Enriched Ptni Alloy Surface and Its Excellent Catalytic Performance in Hydrolytic Hydrogenation of Cellulose

A highly efficient, selective and stable PtCoNi/MWCNTs nanocatalyst for furfural hydrogenation to furfuryl alcohol under mild reaction conditions