Abstract:A multi-frequency locally resonant (LR) phononic plate is proposed in this paper. The phononic plate consists of periodic arrays of multiple double-cantilevered thin beams attached to a thin homogeneous plate. This proposed phononic plate is simplified and modeled using a plane wave expansion method to enable the calculation of flexural wave band structures. The band gap behavior of the phononic plate is analyzed comprehensively. In addition, an experimental specimen is fabricated using a square aluminum plate with a thickness of 0.9 mm and an area of 840 mm840 mm, and attached to the specimens as periodic arrays of two types of double-cantilevered thin beams made of the same material as the host plate. And the specimen is measured by using a scanning laser Doppler vibrometer to verify the theoretical predictions of band gaps. Investigations of this paper yield the following findings and conclusions: (1) Due to the interaction of low-frequency vibrational modes of attached multiple double-cantilevered beams and flexural vibration of the host plate, the proposed multi-frequency LR phononic plate can exhibit multiple low-frequency flexural wave band gaps (stop bands). It is also found that the band gaps of a multi-frequency LR phononic plate, especially those appearing in a lower frequency range, are generally narrower than that of a single-frequency LR phononic plate with the same type of double-cantilevered beams. (2) The frequency location of band gaps moves to higher frequency range when the thickness of the double-cantilevered beams is increased, or when the length of the double-cantilevered beams is decreased. It is also shown that a very small variation of the thickness (e. g., 0.1 mm) may lead to significant changes of frequency position of the band gaps. (3) When the width of the double-cantilevered beams is enlarged or the number of the double-cantilevered beams is increased, the lower band gap edge will move to a lower frequency range, while the upper band gap edge will move to a higher frequency range. This implies that the bandwidth of the band gaps is broadened. However, at the same time, it is shown that the central frequencies of the band gaps remain almost unchanged. (4) Experimental measurements of the fabricated specimen evidence the existence of two low frequency band gaps, and confirm that the flexural plate vibrations are significantly reduced in the predicted band gaps.

Low frequency band gaps below 10 Hz in radial flexible elastic metamaterial plate

An Inertant Elastic Metamaterial Plate with Extra Wide Low-Frequency Flexural Band Gaps

Forming Low-Frequency Complete Vibration Bandgaps in a thin Nonmetallic Elastic Metamaterial Plate

Band-Gap Properties of Elastic Metamaterials with Inerter-Based Dynamic Vibration Absorbers

Plate-type Elastic Metamaterials for Low-Frequency Broadband Elastic Wave Attenuation.

Low-frequency Tunable Locally Resonant Band Gaps in Acoustic Metamaterials Through Large Deformation

Improving Sound Insulation in Low Frequencies by Multiple Band-Gaps in Plate-Type Acoustic Metamaterials

Hybrid Rod-Plate Lattice Metamaterial with Broadband Vibration Attenuation

The Two-Degree-of-freedom Local Resonance Elastic Metamaterial Plate with Broadband Low-Frequency Bandgaps

Flexural wave suppression by an acoustic metamaterial plate

Excellent Low-Frequency Sound Absorption of Radial Membrane Acoustic Metamaterial

Low-Frequency Flexural Wave Acoustic Insulation Characteristics of a Double-Layer Metamaterial Plate

Band-gap Dynamics and Programming for Low-Frequency Broadband Elastic Metamaterial

A Multi-Band Elastic Metamaterial for Low-Frequency Multi-Polarization Vibration Absorption

A vibration isolation gasket based on elastic metamaterial for low-frequency waves

Low Frequency Band Gaps and Vibration Reduction Properties of A Multi-Frequency Locally Resonant Phononic Plate

Metamaterials for Simultaneous Acoustic and Elastic Bandgaps

Modulating lamb wave band gaps using an elastic metamaterial plate

A new local resonance metamaterial for flat and cylindrical structures depended on elastic chiral spiral beams

A metamaterial for low-frequency vibration damping

Optimization of novel plate acoustic metamaterials and modulation of the low-frequency bandgap