Abstract:A supervisory Model Predictive Control (MPC) approach is developed for an air path system for multi-mode operation in a diesel engine. MPC is a control method based on a predictive dynamic model of system and determines actuator control positions through the optimization of various factors such as tracking performances of target setpoints, moving speed of actuators, limits, etc. Previously, linear MPC has been successfully applied on the air path control problem of a diesel engine, however, most of these applications were developed for a single operation mode which has only one set of control target setpoint values. In reality, a single operation mode cannot cover all requirements of current diesel engines and this complicates practical implementations of linear MPC. The high priority targets for the development of diesel engines are low emissions, high thermal efficiency and robustness. These objectives require multi-mode operations such as a HP EGR (High pressure exhaust gas recirculation) mode in cold coolant condition, a Double EGR mode for sufficient EGR rates, a Diesel Particulate Filter (DPF) regeneration mode for the heat-up of exhaust gas temperature and a rich mode of exhaust gas for Lean NOx Trap (LNT) regeneration. Each engine operation mode requires different target setpoints from the air path, such as air mass flow rate and oxygen concentration. In the multi-mode operation, simple linearization based MPC is limited in the practical application because a linearization point changes depending on target setpoints of each operation mode. This means that a linear model for a specific operation mode is not valid in other operation modes, which have different target setpoints. Moreover, the modern diesel air path system is highly nonlinear and would require a significant number of linear models to adequately represent the entire behavior not only at all operation points of engine speed and load, but also at the various operation modes. In this study, a new scheme is proposed and tested on a diesel engine utilizing combined benefits of a supervisory MPC and component level nonlinear compensators. The developed nonlinear compensators are based on dynamic real-time inversions of individual component models. The control scheme comprises of three parts: a supervisory MPC as the coordination of target setpoints in high-level to achieve the objectives, a component level control of nonlinear compensator, state observation either by virtual sensor or by Electronic Control Unit (ECU) sensor. The test results from an engine test bench and a chassis dynamometer demonstrates that the proposed method works well in multi-mode operation and can be applied with the significant benefit that no mode specific control strategies and calibration are needed. A valuable benefit of this approach can be seen in the calibration effort, particularly during development when the setpoints are not necessarily fixed.

Nonlinear Model Predictive Controller Design for Air System Control of a Gasoline Engine

A Thermal Management Strategy for Proton Exchange Membrane Fuel Cell via Nonlinear Model Predictive Control

Nonlinear Model Predictive Control Based on Variable Gain

An Economic Nonlinear Model Predictive Control Strategy for SI Engines: Model-Based Design and Real-Time Experimental Validation

Nonlinear control approaches for SI engine model with uncertainties

Neural network model based predictive control for multivariable nonlinear systems

Neuro-Internal Model Based Optimal Control for Gasoline Blending Processes

Adaptive and Learning Control for SI Engine Model With Uncertainties

Development of a Model Predictive Airpath Controller for a Diesel Engine on a High-Fidelity Engine Model with Transient Thermal Dynamics

Nonlinear Design Method for Improving Aero-Engine Control Performance

An Integrated Controller Design for a Small Aero-Engine

The Nonlinear Single Controller Of Dgen380 Aero Engine Design

Nonlinear Model Predictive Control of Integrated Diesel Engine and Selective Catalytic Reduction System for Simultaneous Fuel Economy Improvement and Emissions Reduction

Model Predictive Control of an Air Path System for Multi-Mode Operation in a Diesel Engine

Nonlinear Predictive Control of Diesel Engine DOC Outlet Temperature

Engine Control Design Using Globally Linearizing Control and Sliding Mode

Fast Calibration of a Robust Model Predictive Controller for Diesel Engine Airpath

An Adaptive Nonlinear Model Predictive Control Based On Online Svm Regression Algorithm

Model Predictive Control of Diesel Engine Emissions Based on Neural Network Modeling

Neural-Network-Based Predictive Control for PMSM Drives

Research on nonlinear model predictive control of regulated two-stage turbocharging system of diesel engine at high altitudes