Abstract:The recently developed tough and self-healing hydrogels, containing a large number of physical bonds, have found widespread applications in bioengineering and soft electronics. Owing to the sophisticated physical interactions and organization, these hydrogels often demonstrate structural heterogeneities, which strongly influence their mechanical performances. Using poly(N,N-dimethyl acrylamide-co-methacrylic acid) hydrogels (P(DMAA-co-MAAc)) with dynamic hydrogen bonds (H-bonds) as a model system, the structural characterization has been carried out in this study using small-angle X-ray scattering (SAXS) and small-angle neutron scattering (SANS) analyses, along with exploring the influence of the structure on the mechanical properties. By systematically tuning the polymer composition, including the monomer fraction and chemical cross-linking density, two different hydrogel regions with distinct mechanical properties were observed: the swollen regions and shrunk regions. The former was mechanically weak, whereas the latter exhibited a tough behavior. Both types of hydrogels were noted to be highly heterogeneous, which results from the nanoscale spatial polymer concentration fluctuations at ∼100 nm scale. Combined with the contrast variation utilizing SANS, the structure parameters, including the polymer volume fraction of the dense and sparse regions, volume fraction occupied in the space, and average correlation length of the long-range and short-range heterogeneous structures, were explored using a scaling model based on a two-phase system composed of the densely and sparsely cross-linked regions. Using in situ SAXS, the microscopic deformation of the tough and shrunk hydrogels was noted to follow the affine deformation, while a significantly non-affine deformation was observed in the swollen hydrogels, which might have led to the different mechanical performances of these materials.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.macromol.1c01064.Swelling volume ratio of hydrogels 0.14-0.2% during the drying–swelling cycle (Figure S1); FT-IR spectra of PDMAA, PMAAc, and P(DMAA-co-MAAc) and temperature dependence of FT-IR spectrum of P(DMAA-co-MAAc) (Figure S2); semi-empirical quantum chemical calculations for revealing the conformation features and their interaction in water (Figure S3); tensile stress–strain curves of P(DMAA-co-MAAc) hydrogels f-0.1% with various f values (0.12, 0.13, and 0.15) and P(DMAA-co-MAAc) hydrogels 0.14-x with various x values (0.05, 0.1, and 0.15%) (Figure S4); 1D scattering intensity as a function of the scattering vector q under various stretch ratios for the hydrogels f-0.1% with the molar fraction of DMAA varying from 0.12 to 0.15 and hydrogels 0.14-x with the chemical cross-linking density ranging from 0.05 to 0.15% (Figures S5 and S6); stretch-induced structure evolution of the swollen hydrogel 0.14-0 (Figure S7); tensile stress–strain curve of hydrogel 0.14-1% and the corresponding Mooney–Rivlin plot (Figure S8); and structural parameters of the swollen and shrunk hydrogels (Table S1) (PDF)This article has not yet been cited by other publications.

Toughening Hydrogels by Immersing with Oppositely Charged Polymers

Toughening Double Network Hydrogels by Polyelectrolytes

Structure Optimization and Mechanical Model for Microgel-Reinforced Hydrogels with High Strength and Toughness

Ultrastiff, Tough, and Healable Ionic-Hydrogen Bond Cross-Linked Hydrogels and Their Uses As Building Blocks to Construct Complex Hydrogel Structures

Tough Supramolecular Hydrogels with Excellent Self-Recovery Behavior Mediated by Metal-Coordination Interaction

Polyzwitterions as a Versatile Building Block of Tough Hydrogels: From Polyelectrolyte Complex Gels to Double-Network Gels

Multi-physically Cross-Linked Hydrogels Simultaneously with MPa Level Mechanical Strengths and High Equilibrium Water Content above 70 %

Dual Ionically Cross-linked Double-Network Hydrogels with High Strength, Toughness, Swelling Resistance, and Improved 3D Printing Processability

Tough Hydrogels with Dynamic H-Bonds: Structural Heterogeneities and Mechanical Performances

Dually cross-linked single network poly(acrylic acid) hydrogels with superior mechanical properties and water absorbency

Mechanical Properties of a Supramolecular Nanocomposite Hydrogel Containing Hydroxyl Groups Enriched Hyper-Branched Polymers

Selected Phase Separation Renders High Strength and Toughness to Polyacrylamide/Alginate Hydrogels with Large-Scale Cross-Linking Zones

Tough supramolecular hydrogels of poly(N,N-dimethylacrylamide)-grafted poly(methacrylic acid) with cooperative hydrogen bonds as physical crosslinks

Ultra Stretchable, Tough and Self-Healable Poly(acrylic Acid) Hydrogels Cross-Linked by Self-Enhanced High-Density Hydrogen Bonds

Stretchable and tough polystyrene hydrogels by introducing polyacrylamide network

High‐Strength, Thermally Activated Shape Memory Hydrogels Based on Hydrogen Bonding Between MAAc and NVP

Ultra-stiff and tough hydrogels based on small but strong hydrophobic associations via low-reactive hydrophilic monomer

High-performance Poly(acrylic Acid) Hydrogels Formed with a Block Copolymer Crosslinker Containing Amino-Acid Derivatives

A facile method to fabricate high performance PVA/PAA-AS hydrogel via the synergy of multiple hydrogen bonding and Hofmeister effect

Modification of Hydrophobic Hydrogels into a Strongly Adhesive and Tough Hydrogel by Electrostatic Interaction

Plastic-Like Supramolecular Hydrogels with Polyelectrolyte/Surfactant Complexes as Physical Cross-links