Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

Effect of Five Different Additives on the Sintering Behavior of Coal Ash Rich in Sodium under an Oxy-Fuel Combustion Atmosphere

Mechanism of Na2O/CaO Ratio Affecting Ash Fusing Characteristics During Ash Deposition and Slagging in Municipal Solid Waste Incinerator

Effects of Na and Fe on the Formation of Coal-Derived Soot in a Two-Stage Flat-Flame Burner

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Experimental Investigation of Pore Structure During High Sodium Coal Ash Sintering with and Without Calcium Oxide Additive Through XCT Technology

Effects of Sodium Carbonate and Sodium Chloride Additives on Alkaline Fusion of Coal Fly Ash

Experiments on the Effect of Chemical Components of Coal Ash on the Sintering Temperature

Effect of different additives on ash fusion characteristic and mineral phase transformation of iron-rich Zhundong coal

Sintering Behavior Of Ash From Combustion Of Jincheng Coal And Pine Sawdust Blends

Visual Investigation of the Growth of Ash Deposits and Characteristics of Fly Ash with CaO Additives

Influence of Ash Composition on the Sintering Behavior During Pressurized Combustion and Gasification Process

Effect of Chemical Compositions on Ash Fusibility Characterization of a Jincheng Anthracite During Combustion and Gasification

Experiments of the effects of reaction atmosphere on the coal ash sintering temperature

Impact of ammonium sulfate and kaolin on ash deposition during co-firing of straw pellets and pulverized coal

The characteristics of mineralogy, morphology and sintering during co-combustion of Zhundong coal and oil shale

Effects of modified kaolin adsorbents on sodium adsorption efficiency and ash fusion characteristics during Zhundong coal combustion

Effect of Chlorine, Sulfur, Moisture and Ash Content on the Partitioning of As, Cr, Cu, Mn, Ni and Pb During Bituminous Coal and Pickling Sludge Co-Combustion

Effect of additives on flow characteristics and sodium capture efficiency of high alkali coal ash slag

12th International Conference on Fluidized Bed Technology EFFECT OF ADDITIVES ON THE ASH FUSION TEMPERATURE

Effect of Biomass Ashes on Sintering Characteristics of High/low Melting Bituminous Coal Ash

Inhibition of Sodium Release from Zhundong Coal Via the Addition of Mineral Additives: A Combination of Online Multi-Point LIBS and Offline Experimental Measurements