Abstract:BackgroundGlaucoma is the primary cause of irreversible blindness worldwide associated with high intraocular pressure (IOP). Elevated intraocular pressure will affect the normal aqueous humor outflow, resulting in deformation of iris. However, the deformation ability of iris is closely related to its material properties. Meanwhile, the passive deformation of the iris aggravates the pupillary block and angle closure. The nature of the interaction mechanism of iris deformation and aqueous humor fluid flow has not been fully understood and has been somewhat a controversial issue. The purpose here was to study the effect of IOP, localization, and temperature on the flow of the aqueous humor and the deformation of iris interacted by aqueous humor fluid flow.MethodsBased on mechanisms of aqueous physiology and fluid dynamics, 3D model of anterior chamber (AC) was constructed with the human anatomical parameters as a reference. A 3D idealized standard geometry of anterior segment of human eye was performed. Enlarge the size of the idealization geometry model 5 times to create a simulation device by using 3D printing technology. In this paper, particle image velocimetry technology is applied to measure the characteristic of fluid outflow in different inlet velocity based on the device. Numerically calculations were made by using ANSYS 14.0 Finite Element Analysis. Compare of the velocity distributions to confirm the validity of the model. The fluid structure interaction (FSI) analysis was carried out in the valid geometry model to study the aqueous flow and iris change.ResultsIn this paper, the validity of the model is verified through computation and comparison. The results indicated that changes of gravity direction of model significantly affected the fluid dynamics parameters and the temperature distribution in anterior chamber. Increased pressure and the vertical position increase the velocity of the aqueous humor fluid flow, with the value increased of 0.015 and 0.035 mm/s. The results act on the iris showed that, gravity direction from horizontal to vertical decrease the equivalent stress in the normal IOP model, while almost invariably in the high IOP model. With the increased of the iris elasticity modulus, the equivalent strain and the total deformation of iris is decreased. The maximal value of equivalent strain of iris in high IOP model is higher than that of in normal IOP model. The maximum deformation of iris is lower in the high IOP model than in the normal IOP model.ConclusionThe valid model of idealization geometry of human eye could be helpful to study the relationship between localization, iris deformation and IOP. So far the FSI analysis was carried out in that idealization geometry model of anterior segment to study aqueous flow and iris change.

SIMULATING THE EFFECTS OF ELEVATED INTRAOCULAR PRESSURE ON OCULAR STRUCTURES USING A GLOBAL FINITE ELEMENT MODEL OF THE HUMAN EYE

Towards Understanding the Aetiology of High Myopic Strabismus Using Mechanical Analysis and Finite Element Modelling

The finite element analysis of the pathology and treatment of high myopia esotropia

Finite element analysis of trans-lamina cribrosa pressure difference on optic nerve head biomechanics: the Beijing Intracranial and Intraocular Pressure Study

Modeling individual-specific human optic nerve head biomechanics. Part I: IOP-induced deformations and influence of geometry

Optic nerve head damage relation to intracranial pressure and corneal properties of eye in glaucoma risk assessment

A Mechanistic Model of Aqueous Humor Flow to Study Effects of Angle Closure on Intraocular Pressure

Fluid and structure coupling analysis of the interaction between aqueous humor and iris

The Impact of Intraocular Pressure Changes on Corneal Biomechanics in Primary Open-angle Glaucoma

Analysis of the effects of finite element type within a 3D biomechanical model of a human optic nerve head and posterior pole

Finite Element Biomechanics of Optic Nerve Sheath Traction in Adduction

In Situ-Crosslinked Hydrogel-Induced Experimental Glaucoma Model with Persistent Ocular Hypertension and Neurodegeneration.

Effects of elevated intraocular pressure on alpha ganglion cells in experimental glaucoma mice

Impact of elevated IOP on lamina cribrosa oxygenation; A combined experimental-computational study on monkeys

The influence of different intraocular pressure on lamina cribrosa parameters in glaucoma and the relation clinical implication

Elevated IOP Alters the Material Properties of Sclera and Lamina Cribrosa in Monkeys

A novel intraocular pressure predicting method based on hyperelastic mechanical model of cornea

Image-Based Modeling of Optic Nerve Head Mechanics Following Lumbar Puncture

Modeling individual-specific human optic nerve head biomechanics. Part II: influence of material properties

Introducing the Biomechanics-Function Relationship in Glaucoma: Improved Visual Field Loss Predictions from intraocular pressure-induced Neural Tissue Strains

The Dynamic Scleral Extracellular Matrix Alterations in Chronic Ocular Hypertension Model of Rats.