Abstract:Narrow channel heat exchange technology is one of the key technologies for the development of integrated small modular reactors (SMR). The 'wall heat flux partitioning' (WHFP) model in conjunction with an Eulerian-Eulerian Multiphase Flow (EEMF) method is found to be an important tool for two-phase hydrothermal analysis. In this paper, the accuracy of the EEMF-WHFP method with various sub-models is systemically evaluated over a large database of boiling flows in narrow rectangular channels. Prediction results using a total of 9 model combinations, are compared with data from 22 experimental conditions covering a range of the mass flux of 134.2 to 2200 kgm-2s-1, the inlet fluid subcooling of 7.2 to 74.2 K, the pressure of 0.1 to 14 MPa and the heat flux of 9.54 to 1700 kWm-2 in narrow rectangular channels with gaps of 1.0 to 3.0 mm. The evolution of distributions of void fraction, wall temperature and the net vapor generation (NVG) point along the flow channel is simulated and compared with experimental data. It is found that due to the limitation of the range of applicability of sub-models, certain models produced better prediction results under different pressure ranges than others, and the recommended combinations are given according to the quantitative assessments. In addition, the ability of the model combinations to predict the NVG point, as well as the flow structure and boiling process in narrow channels is investigated. The critical local void fraction near the wall at the NVG point is quantitatively estimated based on numerical results. The research conclusions in this paper can be used in thermal-hydraulic calculations in a wide range of operating pressures covering the applications of compact heat exchangers, flat plate fuels, climbing/falling film plate evaporators and the cooling of microelectronics, among other applications.

Computational Fluid Dynamics Predicting the Distributions of Thinning Locations on the Shell Wall of Feedwater Heaters

Prediction of possible wear sites on the shell wall of feedwater heater due to droplet impingement using CFD models

Predicting Distributions of Wear Sites on Shell Wall of Feedwater Heater in Nuclear Power Plant Using Two Phase Models

Predicting the Wall Thinning Engendered by Erosion–corrosion Using CFD Methodology

CFD investigating the influence of power uprate on impingement wear sites for the feedwater heater in the nuclear power plant

A Two-Phase Methodology to Predict Fac Wear Sites in the Piping System of A Bwr

Predicting Local Distributions of Erosion–corrosion Wear Sites for the Piping in the Nuclear Power Plant Using CFD Models

Application of Local Flow Models in Predicting Distributions of Erosion-Corrosion Locations

Numerical Study on a Semi-Mechanistic Wall Boiling Model Based on Dry-Patch Mechanism for CHF Prediction in Vertical Tube and Fuel Assembly

Numerical Prediction of CHF Based on CFD Methodology under Atmospheric Pressure and Low Flow Rate

Computational fluid dynamic modeling of hydrodynamics in downer reactors

New Models of Droplet Deposition and Entrainment for Prediction of Liquid Film Flow in Vertical Annuli

Numerical Modeling and Experimental Validation of Heat Transfer and Flow Resistance on the Shell Side of a Shell-and-tube Heat Exchanger with Flower Baffles

Prediction of Thermohydraulics in Shell Side of CAP1400 Steam Generator by Two-Fluid Porous Media Model

A Practical Numerical Simulation Approach for 3D Wet Steam Flow

Numerically Investigating the Influence of Local Flow Behaviors on Flow-Accelerated Corrosion Using Two-Fluid Equations

Development of a Three-Field Mechanistic Model for Dryout Prediction in Annular Flow

Numerical Investigation of Flow Boiling Characteristics in Narrow Rectangular Channels Using Two-Fluid Eulerian Cfd Model Covering a Wide Range of Pressures

Predictions of Hydrodynamic Characteristics and Corrosion Rates Using CFD in the Piping Systems of Pressurized-Water Reactor Power Plant

Visual experimental study of droplet impinging on liquid film and analysis of droplet evolution characteristics

An Upwind Eulerian-Eulerian Model For Non-Equilibrium Condensation In Steam Turbines