Abstract:Aluminum matrix composites reinforced with graphene nanoplatelets (GNPs) were prepared by continuous casting and subsequent rolling. Al-GNPs master alloy, prepared by ball milling and cold pressing, was added into Al melts to fabricate the composites. Microstructure evolution of the composites were observed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron back scattered diffraction (EBSD). GNPs distributed uniformly in the as-cast specimen and then transformed into fibers in the rolling direction after deformation and finally a lamellar structure formed in the composites. Raman spectra showed that the structural damage of GNPs mainly came from ball milling. The interface between GNPs and Al was well combined in general while a few microcracks were observed, which reduced the ductility of the composites and no adverse aluminum carbide (Al4C3) was detected at the interface. Stacking faults were observed interior of the aluminum grain, which may due to the existence of plentiful interface introduced by GNPs. Fracture observation revealed that the load transferred from Al matrix to GNPs. The ultimate tensile strength of Al-0.2 wt% GNPs composites was about 36.8% higher than that of pure Al with the same casting and rolling process, which should result from the lamellar structure and load transfer, while the conductivity of the composites decreased slightly, indicating that interface scattering between Al and GNPs is very limited. The investigation results show that Al GNPs composite is potential for high strength and high conductivity application.

Microstructure and Anisotropy of Mechanical Properties of Graphene Nanoplate Toughened Al2O3-based Ceramic Composites

Microstructure and Toughening Mechanisms of Al2O3/(W, Ti)C/graphene Composite Ceramic Tool Material

Preparation and Microstructure Analysis of Graphene Toughened Al2O3/Ti(C,N) Nanocomposite Ceramic Cutting Tool Material

Microstructure Evolution and Properties of Graphene Nanoplatelets Reinforced Aluminum Matrix Composites

Graphene nano-platelets reinforced aluminum composites with anisotropic compressive properties

Preferentially oriented SiC/graphene composites for enhanced mechanical and thermal properties

Improved fracture resistance and toughening mechanisms of GNPs reinforced ceramic composites

Toughness Enhancement and Thermal Properties of Graphene-Cnts Reinforced Al2O3 Ceramic Hybrid Nanocomposites

Alumina-Based Nanocomposite Ceramic Cutting Tool Materials Toughened By Graphene Nanoplates

Microstructural Evolution, Mechanical and Physical Properties of Graphene Reinforced Aluminum Composites Fabricated Via Powder Metallurgy

Microstructure and Mechanical Properties of Graphene Nanoplates Reinforced Pure Al Matrix Composites Prepared by Pressure Infiltration Method

Fabrication and mechanical properties of Al2O3–TiC ceramic composites synergistically reinforced with multi-walled carbon nanotubes and graphene nanoplates

Mechanical and Thermal Properties of Graphene Nanoplates (gnps)/lithium Aluminosilicate (LAS) Composites: an Analysis Based on Mathematical Model and Experiments

Preparation and Mechanical Properties of Graphene-Reinforced Alumina-Matrix Composites

The Reinforcing Effect of Graphene Nano-Platelets on the Cryogenic Mechanical Properties of GNPs/Al2O3 Composites

Effect of Interfacial Microstructure on the Mechanical Properties of GNPs/Al Composites

Macro-micro-nano Multistage Toughening in Nano-Laminated Graphene Ceramic Composites

Microstructure and Thermal Conductivity of Al–Graphene Composites Fabricated by Powder Metallurgy and Hot Rolling Techniques

Mechanical Properties and Conductivity of Graphene/al-8030 Composites with Directional Distribution of Graphene

Microstructure and Properties of a Graphene Platelets Toughened Boron Carbide Composite Ceramic by Spark Plasma Sintering

Microstructure Evolution and Superior Tensile Properties of Low Content Graphene Nanoplatelets Reinforced Pure Ti Matrix Composites