Abstract:Liquid fuels are good candidates for combustion-based miniature power sources due to their large specific energy. In this study, combustion characteristics of n-C4H10/air mixtures in a tube (ID = 6 mm) partially filled with wire mesh was experimentally explored over an equivalence ratio of phi = 0.5-1.5. In most cases, partially submerged flames and surface flames were observed on the downstream side of the porous media. An external diffusion flame was established under high inlet velocities for fuel-rich mixtures of 1.2 <= phi <= 1.5. The flame with a center convex started to appear at a certain inlet velocity due to the relatively higher local velocity, which was a result of the rolling up method of the wire mesh. Moreover, a lower extinction limit of 0.1 m/s was achieved over 0.9 <= phi <= 1.2, whereas the blow-off limit rose almost linearly up to 0.8 m/s with the equivalence ratio even on the fuel-rich side. The underlying mechanisms for this tendency were comprehensively analyzed from the preheating effect, heat loss effect, volumetric expansion effect as well as the support effect from the external diffusion flame. Furthermore, for an identical inlet velocity, the wall temperature first rose until phi = 1.1 and then decreased when phi > 1.1. Under a constant equivalence ratio, both the maximum wall temperature and the exhaust gas temperature increased with an increasing inlet velocity. However, for an identical inlet velocity, the exhaust gas temperature at low and moderate inlet velocities remained almost invariable versus the equivalence ratio. This was speculated to be the relatively small variation of heat loss ratio versus equivalence ratio. In summary, these findings enriched the knowledge of n-C4H10/air combustion in small tubes partially filled with porous media.

Effect of Inlet Temperature on Combustion Efficiency of Lean H2/air Mixtures in a Micro-Combustor with Wall Cavities

Effect of Inlet Mixture Temperature on Combustion Efficiency Of Lean H2/air Flames in a Micro Cavity-Combustor

Effect of Oxygen Enrichment on Combustion Efficiency of Lean H2/N2/O2 Flames in a Micro Cavity-Combustor

Effect of the Cavity Depth on the Combustion Efficiency of Lean H2/air Flames in a Micro Combustor with Dual Cavities

Effect of Reduced Pressures on the Combustion Efficiency of Lean H-2/Air Flames in A Micro Cavity-Combustor

A Numerical Investigation on Combustion Characteristics of H-2/Air Mixture in A Microcombustor with Wall Cavities

Experimental and numerical investigation on combustion characteristics of premixed hydrogen/air flame in a micro-combustor with a bluff body

Numerical Investigation on Mixing Performance and Diffusion Combustion Characteristics of H-2 and Air in Planar Micro-Combustor

Enhancement of Hydrogen Combustion Efficiency by Helium Dilution in a Micro-Combustor with Wall Cavities

Combustion characteristics of hydrogen/air mixture in a micro-combustor with cavities

Experimental and Numerical Studies of Hydrogen/Air Combustion in a Micro-Combustor With a Bluff Body

Experimental Study on the Propagation Characteristics of Non-Premixed H2/air Flames in a Curved Micro-Combustor

Experimental Investigation of Low-Temperature Autoignition in Turbulent Premixed Swirling Flames

Experimental Study on Combustion Characteristics of N-C4h10/air Mixtures in a Meso-Scale Tube Partially Filled with Wire Mesh

Effect of the Cavity Aft Ramp Angle on Combustion Efficiency of Lean Hydrogen/air Flames in a Micro Cavity-Combustor

Effect of external surface emissivity on flame-splitting limit in a micro cavity-combustor

Effects of Flow Rate and Fuel/air Ratio on Propagation Behaviors of Diffusion H-2/air Flames in a Micro-Combustor

Flame Stability of Methane/Air Mixture in a Heat-Recirculating-Type Mesoscale Channel with a Bluff-Body

Combustion performances of a novel micro-combustor with a backward facing step and an exhaust gas recirculation channel

Experimental and Numerical Investigations of Hydrogen–air Premixed Combustion in a Converging–diverging Micro Tube

Numerical Investigation on Flame Propagation Characteristics of Non-Premixed Hydrogen and Air in a Curved Micro-Combustor