Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

The Hydrogen Absorption Behavior of High Nb Contained Titanium Aluminides under High Pressure and Temperature

Experimental and Theoretical Investigation on the Enhanced Hydrogen Storage Performance of Ti–Cr–Mn–Fe-Based Alloys Modified by Nb Substitution

Microstructure Evolution and Hot Deformation Behavior of High Nb Contained TiAl Alloys Hydrogenated at High Temperature

Effect of Β-Phase Stabilizing Elements and High Temperature (1373–1693 K) on Hydrogen Absorption in TiAl Alloys

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Microstructure and Mechanical Properties of Ti44Al6Nb1Cr2V Alloy after Gaseous Hydrogen Charging at 1373–1693 K

Hydrogenation Behavior of Ti–44Al–6Nb Alloy and Its Effect on the Microstructure and Hot Deformability

Deformation Behavior and Microstructural Evolution of Hydrogenated Ti44Al6Nb Alloy During Thermo-Compression at 1373–1523 K

Influence of Temperature and Hydrogen Pressure on the Hydriding/dehydriding Behavior of Ti-doped Sodium Aluminum Hydride

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Multiphase and Microstructure Effects on the Hydrogen Absorption/desorption Behavior of a Ti–22Al–27Nb Alloy

Changes in Microstructure, Ductility and Hydrogen Permeability of Nb–(Ti, Hf)Ni Alloy Membranes by the Substitution of Ti by Hf

Hydrogen Enhanced the Room-Temperature Compressive Properties of Ti44Al6Nb Alloy

Hydrogen Absorption and Desorption in a B2 Single-Phase Ti–22Al–27Nb Alloy Before and after Deformation

Design of Hydrogen Permeable Nb–Ni–Ti Alloys by Correlating the Microstructures, Solidification Paths and Hydrogen Permeability

Influence of Annealing Treatment on the Microstructure and Hydrogen Storage Performance of Ti1.02Cr1.1Mn0.3Fe0.6 Alloy for Hybrid Hydrogen Storage Application

Hydrogen Storage Properties of Ti-Cr-Mn-M (M=V, Fe, Ni, Cu) Alloys

Hydrogen Absorption/desorption Behavior of Ti–22Al–27Nb Alloys with Β0 Single-Phase and Β/o Two-Phase Microstructures

Designing Hydrogen Permeation Barriers in Titanium Aluminium Nitride through First Principles Density Functional Theory Calculations

Evolution of Unidirectional Solidification Microstructure and Hydrogenated Treatment of Nb-Ti-Co Quasiperitectic Alloys

Microstructures with Martensitic Features Induced by Absorption of a Large Amount of Hydrogen in a B2 Single-Phase Ti-22Al-27Nb Alloy