Abstract:A novel micro/nanoscale rough structured superhydrophilic hybrid-coated mesh that shows underwater superoleophobic behavior is fabricated by spray casting or dipping nanoparticle–polymer suspensions on stainless steel mesh substrates. Water droplets can spread over the mesh completely; meanwhile, oil droplets can roll off the mesh at low tilt angles without any penetration. Besides overcoming the oil-fouling problem of many superhydrophilic coatings, this superhydrophilic and underwater superoleophobic mesh can be used to separate oil and water. The simple method used here to prepare the organic–inorganic hybrid coatings successfully produced controllable micro-nano binary roughness and also achieved a rough topography of micro-nano binary structure by controlling the content of inorganic particles. The mechanism of oil–water separation by the superhydrophilic and superoleophobic membrane is rationalized by considering capillary mechanics. Tetraethyl orathosilicate (TEOS) as a base was used to prepare the nano-SiO2 solution as a nano-dopant through a sol-gel process, while polyvinyl alcohol (PVA) was used as the film binder and glutaraldehyde as the cross-linking agent; the mixture was dip-coated on the surface of 300-mesh stainless steel mesh to form superhydrophilic and underwater superoleophobic film. Properties of nano-SiO2 represented by infrared spectroscopy and surface topography of the film observed under scanning electron microscope (SEM) indicated that the film surface had a coarse micro–nano binary structure; the effect of nano-SiO2 doping amount on the film’s surface topography and the effect of such surface topography on hydrophilicity of the film were studied; contact angle of water on such surface was tested as 0° by the surface contact angle tester and spread quickly; the underwater contact angle to oil was 158°, showing superhydrophilic and underwater superoleophobic properties. The effect of the dosing amount of cross-linking agent to the waterproof swelling property and the permeate flux of the film were studied; the oil–water separation effect of the film to oil–water suspension and oil–water emulsion was studied too, and in both cases the separation efficiency reached 99%, which finally reduced the oil content to be lower than 50 mg/L. The effect of filtration times to permeate flux was studied, and it was found that the more hydrophilic the film was, the stronger the stain resistance would be, and the permeate flux would gradually decrease along with the increase of filtration times.

Superhydrophilic and Underwater Superoleophobic Titania Nanowires Surface for Oil Repellency and Oil/Water Separation

Fabrication of a Novel Superhydrophobic and Superoleophilic Surface by One-Step Electrodeposition Method for Continuous Oil/water Separation

Ni-Al Layered Double Hydroxides (ldhs) Coated Superhydrophobic Mesh with Flower-Like Hierarchical Structure for Oil/water Separation

A self-cleaning TiO2 coated mesh with robust underwater superoleophobicity for oil/water separation in a complex environment

Superhydrophilic anti-corrosive and superhydrophobic durable TiO2/Ti mesh for oil/water separation

Micro/Nanoscale Structured Superhydrophilic and Underwater Superoleophobic Hybrid-Coated Mesh for High-Efficiency Oil/Water Separation

Under-oil Superhydrophilic TiO2/poly(sodium Vinylphosphonate) Nanocomposite for the Separation of Water from Oil

Superhydrophilic and Underwater Superoleophobic Poly(propylene) Nonwoven Coated with TiO 2 by Atomic Layer Deposition

Facile Preparation of Durable Superhydrophobic Coating by Liquid-Phase Deposition for Versatile Oil/Water Separation

Superhydrophilicity and Underwater Superoleophobicity TiO2/Al2O3 Composite Membrane with Ultra Low Oil Adhesion for Highly Efficient Oil-in-water Emulsions Separation

Application of Superhydrophobic Mesh Coated by PDMS/TiO2 Nanocomposites for Oil/Water Separation

A durable Ni3S2 coated mesh with reversible transition between superhydrophobicity and underwater superoleophobicity for efficient oil-water separation

Multi-functional TiO2-based Superoleophobic/Superhydrophilic Coating for Oil-water Separation and Oil Purification.

Dual-functional underliquid superhydrophobic and superoleophobic stainless steel mesh decorated with Ni3S2 nanorods for continuous oil/water separation

Superlyophobic anti-corrosive and self-cleaning titania robust mesh membrane with enhanced oil/water separation

Potocatalytic antifouling membrane with dense nano-TiO2 coating for efficient oil-in-water emulsion separation and self-cleaning

Stainless steel mesh supported TiO2 nanowires membrane with ultra-high flux for separation of oil-in-water mixtures and emulsions

Superhydrophobic Polybenzoxazine/TiO2 Coatings with Reversible Wettability for High-Flux Oil/Water Separation

Preparation of Underwater Superoleophobic Membranes Via TiO2 Electrostatic Self-Assembly for Separation of Stratified Oil/water Mixtures and Emulsions

One-step fabrication of coating-free mesh with underwater superoleophobicity for highly efficient oil/water separation

Facile Fabrication of SWCNT Film-Based Superhydrophobic Cotton Fabrics for Oil/water Separation and Self-Cleaning