Abstract:Total knee arthroplasty (TKA) has been a successful intervention to relieve pain and restore function in patients with end-stage knee arthritis. Over the years with experience, the principles and practices of this operation have evolved, but some fundamentals remain consistent. This includes the concepts of joint alignment and ligament balance that are important factors in the successful outcome of TKA, but some debate still exists concerning the optimal alignment and balance targets for each patient. While static bone resections in the coronal and sagittal planes position the components, soft-tissue management balances the knee joint. There is a close interplay with these two maneuvers, which require an understanding of the implications. While bone resection along the mechanical axis may necessitate soft-tissue releases to achieve appropriate alignment with fixed deformities, kinematic or anatomic alignment (there are several nomenclatures) adjusts the bone cuts with less need for soft-tissue releases to achieve a similar appropriate alignment. However, regardless of surgical plan for bone resection, it is important to understand the implications of fixed coronal and sagittal deformities, and how to achieve the ultimate correction and alignment. Fixed deformities are rarely limited to a single plane. Significant varus or valgus malalignment on the coronal plane is very often associated with sagittal plane and torsional deformities. Correction of the deformity should be done as completely as possible, because no residual degree of a fixed deformity will resolve successfully following surgery. While conventional manual instrumentation has been traditionally used to determine intraoperative limb alignment, the introduction of innovative technologies, such as robotic TKA, offers promises of increased accuracy and efficiency in performing the surgery. The use of preoperative imaging or intraoperative bone mapping in robotic TKA creates a patient-specific 3D reconstruction of the knee with optimal bone resection and implant positioning. One of the intents of innovative technology is to quantify the qualitative feel of the ligament balance by way of numerical gap measurements. With 3D preoperative planning, projected numerical gap measurements demonstrate the virtual distances between the proposed bone resection in the medial and lateral compartments of the knee in flexion and extension. In contrast, an intraoperative kinetic balancing system has been introduced with a variety of TKA systems. This technology offers surgeons a quantitative assessment of load across the medial and lateral joint throughout the arc of motion and is used after bone resection with the trial components in place. The new technologies in TKA are very attractive and are constantly evolving. Nevertheless, some limitations persist and could be improved by artificial intelligence and predictive modeling. At this time, the outcomes of robotic TKA have not translated to long-term functional outcomes compared with conventional TKA. Therefore, regardless of the technologies employed, the principles of manual TKA prevail. Article published online: 19 January 2024 © 2024. Thieme. All rights reserved. Thieme Medical Publishers, Inc. 333 Seventh Avenue, 18th Floor, New York, NY 10001, USA

Practice of Preoperative Strategy Based on Total Knee Arthroplasty

Intra- and inter-operator reliability of three-dimensional preoperative planning in total knee arthroplasty

Reliable prediction of implant size and axial alignment in AI-based 3D preoperative planning for total knee arthroplasty

Pre-operative simulation using a three-dimensional printing model for surgical treatment of old and complex tibial plateau fractures

Total Knee Replacement for Posttraumatic Degenerative Arthritis of the Knee.

Two-Dimensional Versus Three-Dimensional Preoperative Planning In Total Hip Arthroplasty

Virtual Total Knee Replacement System Based on VTK

Planned prosthesis size in modified 3D printed patient-specific instrumentation-assisted total knee arthroplasty:analysis of consistency with intraoperative size

The current role of CT in total knee arthroplasty

Development and Validation of an Artificial Intelligence Preoperative Planning and Patient-Specific Instrumentation System for Total Knee Arthroplasty

Application strategy of finite element analysis in artificial knee arthroplasty

Comparison of three-versus two-dimensional pre-operative planning for total hip arthroplasty

3D preoperative plan assisted total knee arthroplasty after knee arthrodesis with patella absence: a case report

The accuracy of bony resection and component size planning of total knee arthroplasty assisted with a novel designed patient-specific instrumentation

The Principles of Total Knee Arthroplasty Prevail with the Introduction of Innovative Technology

Accuracy analysis of artificial intelligence-assisted three-dimensional preoperative planning in total hip replacement

The role and value of surgeon-engineer interaction during preoperative planning of patient-specific instrumentation assisted total knee arthroplasty

The Effect of Preoperative Rehabilitation Training on the Early Recovery of Joint Function after Artificial Total Knee Arthroplasty and Its Effect Evaluation

Effect of 3D Printed Patient-Specific Cutting Guide on Patellar Height and Joint Line Position in Total Knee Arthroplasty

Application of multiplanar reconstruction and 3D printing in anterior cruciate ligament revision

[Influence of preoperative range of motion on the early clinical outcome of total knee arthroplasty].