Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

Effects of Blending Ratio and Injection Pressure on Diesel/n-Butanol Low Temperature Combustion

Mechanism of Effects of N-Butanol Properties on Low Temperature Combustion in a Diesel Engine

Effects of N-Butanol on Combustion and Emissions of Low Temperature Combustion

Effects of Injection Timing and Pressure on Combustion and Emissions on an Engine Fueled with Diesel/Gasoline/n-Butanol Blends

Investigation on the Effects of Pilot Injection on Low Temperature Combustion in High-Speed Diesel Engine Fueled with N -Butanol–diesel Blends

Effect of Injection Parameters on Low Temperature Combustion Fuelled with Diesel Blended Fuel

Experimental study of n-butanol addition on performance and emissions with diesel low temperature combustion

Effects of fuel properties on combustion and pollutant emissions of a low temperature combustion mode diesel engine

Effects of EGR Rates on Combustion and Emission Characteristics in a Diesel Engine with N-Butanol/pode3-4/diesel Blends

Effect of Intake Oxygen Concentration on Diesel–n-Butanol Blending Combustion: an Experimental and Numerical Study at Low Engine Load

Regulated and Unregulated Emissions from a Compression Ignition Engine under Low Temperature Combustion Fuelled with Gasoline and N-Butanol/gasoline Blends

Combustion Characteristics of Butanol-Diesel Blend Fuel Based on EGR

Effects of N-butanol Premixed Charge on Indicated Thermal Efficiency and Emission of Light Duty Diesel Engine

Potential of N-Butanol/diesel Blends for CI Engines under Post Injection Strategy and Different EGR Rates Conditions

Effect of Two-Stage Injection on Combustion and Emissions under High Egr Rate on A Diesel Engine by Fueling Blends of Diesel/Gasoline, Diesel/N-Butanol, Diesel/Gasoline/N-Butanol and Pure Diesel

An Experimental and Numerical Study on the Effects of Fuel Properties on the Combustion and Emissions of Low-Temperature Combustion Diesel Engines

EFFECTS OF N-BUTANOL CONTENT ON THE DUAL-FUEL COMBUSTION MODE WITH CNG AT TWO ENGINE SPEEDS

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Effects of Intake Components on Combustion and Emission Characteristics in an n -Butanol/Diesel Blend Fueled Engine

Experimental Study Of The Effect Of Intake Oxygen Concentration On Engine Combustion Process And Hydrocarbon Emissions With N-Butanol-Diesel Blended Fuel

Experimental Study on the Performance of and Emissions from a Low-Speed Light-Duty Diesel Engine Fueled with N-Butanol–diesel and Isobutanol–diesel Blends