Rapid Manufacturing of Mold & Die Based on PSFP

徐文骥,金洙吉,邓琦林,方建成,卢毅申

DOI: https://doi.org/10.3969/j.issn.1005-2402.2002.03.010

2002-01-01

Abstract:The technique of rapid manufacturing of mold and die with PSFP (plasma_spray forming part) are studied. The experiments are carried using Ni01(Ni_Fe_Cr_B_Si) alloy powder as spraying material. Some key technologies to the processes are discussed.

What problem does this paper attempt to address?

Manufacture Of Rapid Metal Mold Based On Rp Prototype By Plasma Spray

Zhengwei Gu,Renji Zhang,Yongnian Yan,Xiangguo Dai

2003-01-01

Abstract:The process of rapid metal mold making based on RP prototype by plasma spray is an innovational technology of mold manufacturing. The process can reduce lead time by as much as 50-60% and save cost by 60% compared with traditional methods. It provides a fast, accurate, cost-efficient route for metal tools manufacturing, and hence it is quite fit for the new products development and low volume urgent parts production. In this paper, the process and its key factors were discussed in detail. Some experimental stainless steel rapid molds are made via the process. The thickness of stainless steel sprayed layer reaches to 5mm and surface hardness is HRC 34.4 and surface roughness comes to Ra0.2 after polishing.
Rapid Metal Tooling by Applying Plasma Spraying and Rapid Prototyping/rapid Tooling Technology for Metal Sheet Forming

Z Gu,X Dai,R Zhang,Y Yan

DOI: https://doi.org/10.1177/095440540421800505

2004-01-01

Abstract:To manufacture the metal mould for high-quality metal sheet parts forming at low cost with a short production cycle, an innovative method of mould manufacturing, based on rapid prototyping (RP)/rapid tooling (RT) technology by plasma spraying is proposed in this paper. First, the technological process of the rapid metal mould manufacturing is introduced, and the key technologies of the process such as RP fabrication technology, unbaked ceramic transition mould process, plasma spraying and back-up process are also introduced. Then, experimental moulds for the metal sheet parts forming are successfully made via this process, and examination and analysis of a mould is carried out. It proves that the method of manufacturing a rapid mould for metal sheet parts forming by plasma spraying and RP/RT technology is a successful technique.
Rapid Tooling of Molds Using Plasma Spray for Sheet Metal Drawing

谷诤巍,戴向国,全永义,张人佶

DOI: https://doi.org/10.3321/j.issn:1000-0054.2004.11.006

2004-01-01

Abstract:A plasma spray mold manufacturing process was investigated expermentally to develop rapid tooling for sheet metal drawing with higher surface hardness and longer service life. The process is described with an analysis of its mechanism and critical factors. A stainless steel rapid drawing mold of a part with a complex curved surface was then successfully made. The key step in the process is the spraying which makes a thick, high-quality mold surface layer. The results show that the quality of the stainless steel surface layer in the mold is very good, with a thickness of 5 mm, an average hardness of HRC 34.4, and a surface roughness of 0.2 μm after polishing. Laser remelting can also further improve surface quality and wear-resistance.
Rapid hard tooling by plasma spraying for injection molding and sheet metal forming

Haiou Zhang,Guilan Wang,Yunhua Luo,Takeo Nakaga

DOI: https://doi.org/10.1016/S0040-6090(01)00910-5

IF: 2.1

2001-01-01

Thin Solid Films

Abstract:Amidst the harsh competition over the development of new products around the world, rapid prototyping, especially rapid tooling methods have received widespread attention. Amongst the rapid hard tooling methods, thermal spraying can manufacture metal molds without limitation of pattern size. However, it has the disadvantage that only soft metals with low melting points such as zinc alloy can be sprayed to original mold, such as a rapid prototyping model or a natural material pattern, due to their lack of heat resistance and shrinkage of spray metals. So the wear resistance of spray tool is poor, it can be used only for trial or small-lot production. In this study, attempts were made to improve the heat resistance by using composite materials made of ceramic and metal powders as the sprayed original mold materials, and using stainless steel, tungsten carbide alloy, iron–nickel–chromium alloy with excellent wear resistance as spraying materials, respectively. The results show that injection molding spray mold and sheet metal forming spray die can be made by transferring from natural patterns and rapid prototyping models. As the durability and dimensional accuracy of the sprayed tools has sharply improved, the tools can be used for mass production.
Rapid manufacture injection mould with built-in conformal cooling channels

Jinhui Liu,Yusheng Shi,Jibing Chen

DOI: https://doi.org/10.19591/j.cnki.cn11-1974/tf.2008.05.010

2008-01-01

Abstract:Injection mould manufacturing encounters the growing competition today, while a rapid way of producing injection mould may win the advantages for it. In this paper, green part of injection mould with conformal cooling channels is manufactured by selective laser sintering (SLS) of commonly used iron powder mixed with polymer powder, and then end-use mould is attained after the green part is debound, sintered at high temperature and infiltrated with modified epoxy resin. The strength and accuracy of the mould were investigated. The rapidness of Rapid Prototyping and Manufacturing (RP and M) and the advantage of SLS are combined in this production method which shortens the production cycle to a week or so and can also setup cooling channels along the contours of the plastic part. Therefore, the process is proved to be a feasible way to manufacture injection mould for small batch production.
Research on Rapid Tooling for Sheet Metal Forming

朱东波,王伊卿,李涤尘,卢秉恒

DOI: https://doi.org/10.3321/j.issn:1004-132x.2002.06.012

2002-01-01

Abstract:Based on the combination of RP(Rapid Prototyping) technology and AMS(Arc Metal Spraying) technology, a rapid manufacturing method of sheet metal forming dies is presented. The method, some key processes of which are explained in detail, proved by practical experiments to be of low-cost and time saving. Dies fabricated by this method are good in performance. The method posseses promising use in trial-manufacture of complex stamping dies and in small serial production of sheet metal parts.
Experimental Studies on the New Technologies of Plasma Arc Spray Forming

QL Deng,YH Zhang,Y Wang,DJ Hu,JC Fang,WJ Xu

DOI: https://doi.org/10.4028/www.scientific.net/kem.259-260.557

2004-01-01

Key Engineering Materials

Abstract:In this paper, the new technologies of plasma are spray forming have been experimentally studied. The processes and main characteristics of rapid forming moulds with precision surface pattern and parts with thin-wall by plasma arc spraying are introduced. The experimental results show that the surface pattern of working moulds formed by plasma arc spraying coincide with the surface pattern of master moulds very much. So this technology can be used in rapid forming large and simple moulds with precision surface pattern. The experimental results also show that plasma arc spraying can be used in rapid forming parts with thin-wall. The parts' shape depended on their master moulds, and the parts' precision depended on both master moulds' precision and coatings' precision. In order to get higher parts' precision, the coating's surface on the side of plasma arc spraying should be machined.
Study on Rapid Metallic Injecting Mold by Plasma Spraying with Low-Cost

罗云华,张海鸥,王桂兰

DOI: https://doi.org/10.3969/j.issn.1672-0121.2001.06.022

2001-01-01

Abstract:Technology of rapid metallic in jecting mold by plasma spraying has been introduced with in jecting trial un-der product condition using rapid in jecting molds with natu-ral leather lines or smooth surface made by the said method by which the produced molds featuring high surface hard-ness,good quality,enduring and low cost and easy to pro-duce will be suitable for new prod uct trial,rapid manufac-ture and volume production of molds in many industries such as automobile and motorcycle.
Rapid precision casting for complex thin-walled aluminum alloy parts

Xuanpu DONG,Naiyu HUANG,Zitian FAN

2004-01-01

China Foundry

Abstract:Based on Vacuum Differential Pressure Casting (VDPC) precision forming technology and the Selective Laser Sintering (SLS) Rapid Prototyping (RP) technology, a rapid manufacturing method called Rapid Precision Casting (RPC) process from computer three-dimensional solid models to metallic parts was investigated. The experimental results showed that the main advantage of RPC was not only its ability to cast higher internal quality and more accurate complex thin-walled aluminum alloy parts, but also the greatly-reduced lead time cycle from Selective Laser Sintering(SLS) plastic prototyping to metallic parts. The key forming technology of RPC for complex thin-walled metallic parts has been developed for new casting production and Rapid Tooling (RT), and it is possible to rapidly manufacture high-quality and accurate metallic parts by means of RP in foundry industry.
Rapid Tooling for Zinc Spin Casting Using Arc Metal Spray Technology

J Wang,XP Wei,P Christodoulou,H Hermanto

DOI: https://doi.org/10.1016/j.jmatprotec.2003.11.014

IF: 6.3

2004-01-01

Journal of Materials Processing Technology

Abstract:A research and development effort was made to investigate the feasibility of rapid tooling for zinc spin casting using stereolithography (SL) and arc metal spray technologies. The study is based on a specific practical case where intermediate tooling processes are required to make an intermediate tool from the SL pattern. The intermediate tool is then used in an arc metal spray process to form a metal master tool that is subsequently used to make spin casting moulds. Different materials and processes were studied to fabricate the intermediate tools. It shows that ceramics, used in investment casting and Shaw process, are suitable materials for the intermediate tools required to make the metal master tools. A preliminary analysis of the dimensional errors confirms the viability of the proposed tooling process chain.
Key Technologies and Application of Metal Arc Spray Tooling

HE Zhong-yun,HONG Jun,LU Bing-heng,SONG Wei

2008-01-01

Abstract:Metal arc spray tooling is a rapid tooling process based on surface replication,which has the advantages of less lead time and lower manufacturing cost compared with conventional die-making methods.Metal arc spray mold is a kind of composite mold with functionally gradient material structure,and consists of metal shell,backing strengthening layer and steel frame.Arc spray tooling process mainly includes: master pattern preparation,surface pretreatment,fabrication of the metal shell,frame fabrication,backing strengthening and post treatment.Metal arc spray tooling can be applied to manufacture injection mold,thermo forming mold and sheet metal stamping mold etc.Finally,the whole arc spray tooling process is described in detail in the rapid tooling example of a large-scale auto body panel mold.
A Note on Rapid Manufacturing Process of Metallic Parts Based on SLS Plastic Prototype

HJ Liu,ZT Fan,NY Huang,XP Dong

DOI: https://doi.org/10.1016/s0924-0136(03)00811-2

IF: 6.3

2003-01-01

Journal of Materials Processing Technology

Abstract:The polystyrene prototypes were produced by selective laser sintering (SLS) rapid prototyping process. According to properties of thermal depolymerisation of prototype material, the rapid manufacturing process for metallic parts was worked out through the combination of rapid prototypes and precise casting technology. After prototypes burned out in precision shell moulds, a series of complicate thin walled Al-alloy parts have been successfully made by vacuum differential pressure casting (VDPC) process. Accuracy of parts and influencing factors were investigated and discussed. The process combines the advantages of producing high-qualified metallic parts with shortening the period of production cycle.
Rapid Manufacturing Method for Water Saving Emitter Mold

魏正英,唐一平,赵万华,卢秉恒

DOI: https://doi.org/10.3321/j.issn:1004-132x.2002.17.003

2002-01-01

Abstract:In order to realize the rapid manufacture of a water saving embedded emitter mold, aiming at the structure characteristics and layout of a complex labyrinth runner on emitter, rapid prototyping and manufacturing (RPM) is utilized to build emitter prototype for experiment and finalization of emitter. Then RT technology is used to fabricate emitter and rapid spray tooling for trial-produce of the emitter.Taking the manufacturing of precision mould as the core,emitter CAD parameter as the driving design and rapid manufacture of emitter injection mold are completed at the first time successfully.
Rapid Tooling Die Cast Inserts Using Shape Deposition Manufacturing

Gayle Ramdeen Link,John Fessler,Alex Nickel,Fritz Prinz

DOI: https://doi.org/10.1080/10426919808935240

IF: 4.7832

1998-03-01

Materials and Manufacturing Processes

Abstract:Solid Freeform Fabrication (SFF) platforms such as stereolithography have successfully created rapid tooling injection molding inserts to produce plastic parts. However, the rapid tooling of viable aluminum die casting inserts presents more challenges because of the high pressures and temperatures associated with aluminum die casting. The objective of this research was to optimize the Shape Deposition Manufacturing (SDM) process to produce die cast inserts. SDM is a SFF process which can produce fully dense metal structures with Computer Numerical Control (CNC) accuracy. SDM laser-based metal deposition of tool steel powder was optimized for material properties by a Taguchi based design of experiment utilizing the process parameters of laser power, laser scanning rate, and powder feed rate. An insert was created using the optimized settings and run in a 600 ton die cast machine. The insert was used in the “as deposited” condition without any heat treatments. Over 150 aluminum pieces wsre produced without any signs of insert wear or fatigue.

materials science, multidisciplinary,engineering, manufacturing
Research Status and Application Progress of Plasma Spray Forming Technology

Xuan XU,Jin-yue GU,Wei-hua GU,Yue-ming WANG,Xiang XIONG,Lu XIE

DOI: https://doi.org/10.3969/j.issn.1009-0622.2015.03.010

2015-01-01

Abstract:Plasma Spray Forming, due to its characteristics of high source temperature and fast flow flame, is suitable for the near-net-forming for the refractory material with high hardness. This paper reviews the research status in the four aspects of PSF technology, including spray powder preparation techniques, preparation and processing of the mandrel, the coating process and post-processing. The application advances of thin-walled parts preparation, rapid tooling and some characterized materials are introduced. An accepted theoretical system in the field of PSF has not been established for most researchers have focused on the application, rather than the basic theory. It has not accepted the formation of a theoretical system. Milling, mandrel and post-treatment processes taken into account, the spray parameters-Part Performances Relations Theory should be established by exploring the physical nature of the coating process based on analyzing the phenomenon and data of the powder melted, the various stages of flight and impact.
Application of Patternless Casting Manufacturing in Rapid Tooling

Zhang Renji,Yan Yongnian,Lin Feng,Wu Rendong,Lu Qingping

DOI: https://doi.org/10.3969/j.issn.1009-279X.2006.z1.020

2006-01-01

Abstract:Patternless Casting Manufacturing(PCM)technology is one kind of Rapid Prototyping technology with independent intellectual property rights of our country and it has been widely applied in many fields.The paper firstly presents the new progress of PCM in resent years and then introduce two new rapid tooling technology based on PCM as follows: 1.metal spraying rapid tooling technology based on PCM prototyping 2.metal tooling rapid manufacturing technology based on PCM casting mould.They play an important rule in the advanced manufacturing technology.The new rapid tooling technology in this paper has an important application in the rapid manufacturing of trial-manufacture of car body tooling.
FGM Mould with Fine Veins Rapidly Manufactured by Plasma Spraying

JC Fang,WJ Xu,ZY Zhao,L Wang

DOI: https://doi.org/10.4028/www.scientific.net/kem.291-292.609

2005-01-01

Key Engineering Materials

Abstract:There is the advantage of continuity in organic structure and mechanical property for functionally gradient materials (FGMs), but it is unable to be used in the mould industry for the difficulty of the second machining up to now. In this study, a novel technology of FGM mould with fine veins fabricated by plasma spraying has been developed, which can easily realize the integration of FGM forming and deep machining of the mould. According to applied characteristic of plastic injection mould, WC-12%Co/NiCrAl powders are selected and the reasonable FGM coating has been prepared. Spraying processes have been investigated, such as fabrication of spray mould with fine veins, FGM forming, backing and demoulding, etc. At the same time, the metallography, porosity and microhardness of the spraying layer have been analyzed. The results show that the service performance of the FGM mould is much more excellent than that of the traditional mould, and the life span can also be greatly improved. The research will have a significant influence on the material development in the mould industry.
Rapid Manufacturing Metal Parts Using Sls And Vacuum Pressure Difference Casting Technologies

Yusheng Shi,Haixiao Sun,Naiyu Huang,Shuhuai Huang

2003-01-01

Abstract:How to rapidly fabricate metallic parts through rapid prototyping technology is a highly researched technique. However, at the present time, there are many problems during the direct manufacturing of functional metallic parts with rapid prototyping technology, which limits its practical application. Therefore, the indirect manufacturing technology based on rapid prototyping is still a main means of the fabrication of functional metallic parts. A indirect process of the fabrication of metallic parts based on combining selective laser sintering with vacuum pressure difference casting is researched. Some metallic parts are successfully fabricated using the indirect process. The precision control problems during selective laser sintering and investing casting process are researched and analyzed, and some means to solve the precision problems are put forward.
Development of planar flow casting atomization process for metal powder production

Rongde Li,Qingchun Xiang,FuYu Dong

2008-01-01

Abstract:Conventional planar flow casting (PFC) is one of rapid solidification processes for fabrication of microcrystalline or amorphous ribbons. Based on the conventional PFC process, the planar flow casting atomization (PFCA) process has been developed, which is a brand-new rapid solidification process for metal powder production directly from alloy melts. A prototype experimental apparatus was designed and manufactured. With the apparatus, tin-lead alloy powders were prepared, and the effects of main technological parameters on the powder size distribution and morphology were experimentally studied. The experimental investigations indicate that metal powders produced by the planar flow casting atomization (PFCA) process can naturally be classified by velocity, and the new PFCA process has such features as high productivity and efficiency, low energy consumption, simple operation, short technological process, large gross yield, and low production cost.
Advance in Spray Forming Technology and Its Prospect

王文明,潘复生,Lu Yun,曾苏民

DOI: https://doi.org/10.3969/j.issn.1000-582X.2004.01.027

2004-01-01

Abstract:Spray Forming technology gets involved with new materials preparation techniques in multiple domains such as powder metallurgy, fluent metal atomization, rapid cooling and non-equilibrium solidification. High performance alloy and metal matrix composite with high density, low oxygen content and microstructure featuring rapid solidification can be fabricated by spray forming. Spray forming, which is of short process flow, low cost, high deposition efficiency, flexible manufacture system, becomes a kind of near shape forming and rapid solidification technology with great prospect. Therefore the developing process history of spray forming technology is introduced and the current research and development status of spray forming technology in the fields of aluminum alloy, steel material, magnesium alloy, copper alloy and high temperature alloy and metal matrix composite is described. Multi-layer spray forming and in-situ reaction atomization spray forming are also discussed. In addition, evaluation and prospect for the technology are presented.

Rapid Manufacturing of Mold & Die Based on PSFP

Manufacture Of Rapid Metal Mold Based On Rp Prototype By Plasma Spray

Rapid Metal Tooling by Applying Plasma Spraying and Rapid Prototyping/rapid Tooling Technology for Metal Sheet Forming

Rapid Tooling of Molds Using Plasma Spray for Sheet Metal Drawing

Rapid hard tooling by plasma spraying for injection molding and sheet metal forming

Rapid manufacture injection mould with built-in conformal cooling channels

Research on Rapid Tooling for Sheet Metal Forming

Experimental Studies on the New Technologies of Plasma Arc Spray Forming

Study on Rapid Metallic Injecting Mold by Plasma Spraying with Low-Cost

Rapid precision casting for complex thin-walled aluminum alloy parts

Rapid Tooling for Zinc Spin Casting Using Arc Metal Spray Technology

Key Technologies and Application of Metal Arc Spray Tooling

A Note on Rapid Manufacturing Process of Metallic Parts Based on SLS Plastic Prototype

Rapid Manufacturing Method for Water Saving Emitter Mold

Rapid Tooling Die Cast Inserts Using Shape Deposition Manufacturing

Research Status and Application Progress of Plasma Spray Forming Technology

Application of Patternless Casting Manufacturing in Rapid Tooling

FGM Mould with Fine Veins Rapidly Manufactured by Plasma Spraying

Rapid Manufacturing Metal Parts Using Sls And Vacuum Pressure Difference Casting Technologies

Development of planar flow casting atomization process for metal powder production

Advance in Spray Forming Technology and Its Prospect