Study on Reducing Dead Area of the Brushless Direct Current Motor

徐祖华,盛义发,朱慧玲

DOI: https://doi.org/10.3969/j.issn.1673-0062.2002.04.019

2002-01-01

Abstract:Based on improving BDCM electronic switch circuit,the voltage drop of the transister is compensated,and the nonlinear low-speed scales of BDCM and the dead area of the regulator character are reduced,which are testified by the mathematical model of motor and MATLAB.

What problem does this paper attempt to address?

Research on PWM Method in Brushless DC Motor

WEI Kun,LIN Ping,Xiong Yu,ZHANG Zhong-chao

DOI: https://doi.org/10.3785/j.issn.1008-973x.2005.07.025

2005-01-01

Abstract:The influences of the torque ripples in the commutation interval and non-commutation zones, which were caused by the pulse width modulation(PWM) methods applying in the BLDCM with trapezoidal back-EMF(electromotive force)waveform, were investigated in this work. A new PWM method, PWM_-ON_-PWM, was proposed. Compared with the conventional PWM methods, the ripple current caused by the diode freewheeling in the non-commutation zone can be eliminated, and so the torque ripples can also be decreased by the proposed PWM method. The simulation and experimental results are demonstrated to verify the validity of the proposed PWM method.
Study on Switching Strategy of PMSM and BLDCM

Chengrui Tao,Jianjian Fan,Sunong Yao,Jianhua Wu

DOI: https://doi.org/10.1109/icems56177.2022.9983354

2022-01-01

Abstract:The paper presents a switching control strategy for the driving current of permanent magnet synchronous motor (PMSM), which enlarge the starting torque by adopting trapezoidal drive mode at startup, so that the motor can achieve the same characteristic as brushless direct-current motor (BLDCM) and have more application scenarios. Aiming at the torque ripple problem caused by the change of control parameters in the normal operation and switching process, the paper proposes an adaptive fuzzy control method to ensure the reliability and smoothness. At the same time, the system can obtain better dynamic performance and anti-interference ability. The results show that good operating performance can be guaranteed in the entire operating range.
Reduction of Commutation Torque Ripple in Brushless DC Motors

WANG Zheng-shi,ZHANG Zhao-li,CHEN Hui-ming

DOI: https://doi.org/10.3969/j.issn.1671-7848.2010.03.019

2010-01-01

Abstract:To reduce the influences of the commutation torque ripples in Brushless DC(BLDC),an optimal PWM method is proposed to analyze the PWM influences on the commutation torque ripples.Based on the principle and the BLDC motor equations,the mathematical derivation of the commutation torque ripples is given.To the main problem of torque ripples in brushless DC motor,a new PWM method(PWM-on)is proposed and proved to be efficient in reducing the torque ripple in theory.Based on the efficient TMS320LF28016 DSP control system,the experiment results show that the proposed method is efficient in reducing the torque ripple.
Steady Performance Analysis on Single-Phase Brushless DC Motor

Lijian Wu,Wanbing Jin,Yi Liu,Jianping Ying

DOI: https://doi.org/10.1109/icems12746.2007.4412188

2007-01-01

Abstract:Single-phase brushless DC motor (SPBLDCM) has always been difficult to accurate computer-aided analysis, design and optimization for the lack of appropriate mathematical model of the motor. However, due to simple structure and high efficiency, it is widely used in low cost applications that require low starting torque. In the paper, a linear steady model of SPBLDCM is developed to predict the performance of the motor. It is suitable for the initial design and optimization of the motor geometry because of its low computational complexity. The optimal commutation advance angles for two different objectives, high electromagnetic power and low current ripple, are also presented based on this linear steady model The performance of the prototype is analyzed by both the developed linear steady model and the dynamic model. Both results agree well. The experimental results also validate the effectiveness of the model.
Simulation Brushless DC Motor and Driver with PSpice

丁文浩,吴建华,张式勤

DOI: https://doi.org/10.3969/j.issn.1004-7018.2003.04.002

2003-01-01

Abstract:The part, BLDCMTR, coming with PSpice, is detailed in this paper. And the simulation of the whole system with both BLDCMTR and driver contained is carried out. The simulation results are similar to the experiment ones. All this shows that the whole system simulation will be helpful in designing as well as testing the drivers for BLDCMTRs.
A Novel PWM Scheme to Eliminate the Diode Freewheeling in the Inactive Phase in BLDC Motor

Wei Kun,Hu Chang-sheng,Zhang Zhong-chao

DOI: https://doi.org/10.1007/s11460-006-0019-y

2006-01-01

Frontiers of Electrical and Electronic Engineering in China

Abstract:The brushless DC motor (BLDCM) with trapezoidal electromotive force (back-EMF) waveform is used widely. In principle, when the motor runs in the 120° conduction mode, two of the three phases are active while the other phase is inactive at all times. However, a ripple current occurs in the inactive phase due to the diode freewheeling during the non-commutation period in the traditional pulse width modulation (PWM) methods, which aggravates the torque ripples. A new PWM method is proposed in this paper to eliminate the diode freewheeling during the non-commutation period in the inactive phase. As a result, the torque ripple is suppressed using the proposed method. The simulation and experimental results are demonstrated to verify the validity of the proposed PWM method.
Comparative Performance Evaluation of Hall Effect Sensorless Control Options in Permanent Magnet Brushless DC Motor Drives

Kevin Lee,Feilang Li,Wenxi Yao

DOI: https://doi.org/10.1109/iemdc.2019.8785263

2019-01-01

Abstract:The objective of this paper is to present a comparative and quantitative study on three hall effect sensorless circuit configurations in permanent magnet (PM) brushless dc motor drives, along with four practical pulse width modulation (PWM) techniques. PM brushless direct current (BLDC) motor mathematical model, principles of operation, measurement circuit and logic configurations for three back electromotive force (EMF) zero crossing detection methods, as well as theoretical analysis on various PWM patterns are described. Their performance evaluation on waveform quality, rotor position tracking capability, and torque ripple impact are quantified as functions of motor speed and load variation. Digital time domain simulation models are established with the closed current and speed loops for the evaluation. Experimental results without using any hall effect sensors fully validate the theoretical and simulation findings.
Study on Small Power BLDCM Drive System

Zhongxian Wang,Feng Chai,Yonggeng Wei,Yilin Song

DOI: https://doi.org/10.4028/www.scientific.net/kem.579-580.823

2013-01-01

Key Engineering Materials

Abstract:According to the voltage balance equation, the paper deduces the mathematical model of BLDCM on the basis of analyzing the operation principle. In SIMULINK environment, the BLDCM ontology module is built by adopting the combination of BLDCM state equation with S function method. The built motor ontology module proves to be accurate and reasonable through the analysis of the simulation waveform, which helps to analysis BLDCM electronic commutation, etc. Again taking LM621N as commutation control chip, using PIC microcontroller output variable frequency square wave, and through external input device to adjust the square wave frequency, thus realizes the control of motor speed. A brushless dc motor drive with circuit protection functions is designed by the method of combining hardware and software. Not only the motor work situation of ontology is intuitively reflected, and the development cycle is shorted.
Control Analysis of PM Brushless DC Motor Used in Flywheel Energy Storage System

Changsheng Zhu

2012-01-01

Abstract:Aiming at reducing the current and the torque ripple appeared in flywheel energy storage system running in wide-range speed,after the analysis of torque ripple in the commutation interval,the relation between the torque ripple and the speed was established.A hybrid method was presented that the PWM-on-PWM was chosen to control power devices during low-speed range,while during high-speed range,the overlapping commutation with PWM was used.The control method were evaluated on the effect of reducing the current and the torque ripple during the commutation interval,the Matlab/Simulink model was built,and the running test in low-speed range were tested.The experimental results show that the proposed method can eliminate diodes′ free-wheeling phenomenon and reduce the torque ripple during the commutation interval,it adapts for brushless DC motor in wide speed-range.
New BLDCM Drive Method to Smooth the Torque

ZHANG Xiao-feng,L(U) Zheng-yu

DOI: https://doi.org/10.3969/j.issn.1000-100x.2007.02.036

IF: 5.967

2007-01-01

IEEE Transactions on Power Electronics

Abstract:This paper presents a comprehensive research on torque ripples of brushless dc motor drive in conduction region based on the mathematical models.The phenomenon of torque ripples of conduction exists because of diode free-wheeling happened under the conventional PWM schemes.Through theoretical and mathematical analysis,a new method for reducing the torque ripple in brushless dc motors has been proposed by adding the DC-DC converter that regulates the amplitude of the current.So in such drives,torque ripples are eliminated in conduction region.Effectiveness of the proposed control method is verified by experiments.
A Practical Method to Eliminate the Conduction Torque Ripple in BLDCM Using Cascade Topology

Xiaofeng Zhang,Zhengyu Lu,Yu Ma,Zhaoming Qian

DOI: https://doi.org/10.1109/apec.2008.4522709

2008-01-01

Abstract:This paper presents a comprehensive research on torque ripples of brushless dc motor drive in conduction region based on the mathematical models.The phenomenon of torque ripples of conduction exists because of diode freewheeling happened under the conventional PWM schemes. Through theoretical and mathematical analysis, a new method for reducing the torque ripple in brushless dc motors with a single current sensor has been proposed by adding the DC-DC converter that regulates the amplitude of the current. So in such drives, torque ripples are theoretically eliminated in conduction region. Effectiveness and feasibility of the proposed control method is verified by experiments. Torque ripples due to diode freewheeling current and conventional high-frequency PWM modulation have vanished. So it is preferable for the drive system of high accuracy-controlling BLDCM.
Dynamic characteristics analysis of the brushless DC motor direct drive system

Gui-jie YANG,NLi SU,NLi-zhi SU,Yong-ping LU,Sh-hua GAO

DOI: https://doi.org/10.3969/j.issn.1007-449X.2000.01.001

2000-01-01

Abstract:The mathematical model of a brushless DC motor direct drive system with integral DSP motor controller ADMC 331M is deduced and a full digital vector control brushless DC mo-tor direct drive system is introduced in this paper.The influence of the leading angle (lagging angle) of the current reference signal the parameters and drive mode of the system to the dy-namic characteristics are anal yzed.The results of simulation and experiment indicate that the deterioration of the dynamic characteristics of the system is caused by leading angle(laggingangle)of the current reference signal.With the magnetic field orient control,the brushless DC motor system can obtain a maximum output torque and the best dynamic characteristics.When the gain of the current ratio regulator and enlargement factor of power inverter are in-creased,dynamic characteristics of the system will become better;when the compound drive mode of sine wave plus triple and quintuple harmonics is used,the dynamic characteristics of the system can be improved.
A New BLDC Motor Drives Method Based on BUCK Converter for Torque Ripple Reduction

Zhang Xiaofeng,Lu Zhengyu

DOI: https://doi.org/10.1109/ipemc.2006.4778134

2006-01-01

Abstract:This paper presents a comprehensive analysis on torque ripples of brushless dc motor drives in conduction region and commutation region. A novel method for reducing the torque ripple in brushless dc motors with a single current sensor has been proposed by adding BUCK converter in the front of 3-phase inverter. In such drives, torque ripple suppression technique is theoretically effective in commutation region as well as conduction region. Effectiveness and feasibility of the proposed control method is verified through experiments
Low Power Consumption Control Method for BLDCM with Very Small Inductance and Nonideal Back EMF

Haitao Li,Kanqiang Liu,Hu Liu

DOI: https://doi.org/10.1109/tpel.2024.3372108

IF: 5.967

2024-01-01

IEEE Transactions on Power Electronics

Abstract:Conducting research on reducing the power consumption of the high-speed brushless DC motor (BLDCM) drive system is crucial for the efficient operation of the magnetically suspended control moment gyroscope (MSCMG) in the limited energy environment of space. This paper focuses on studying the losses caused by current harmonics and non-ideal back electromotive force (EMF) in the BLDCM, and proposes a low power consumption control method to mitigate these losses. Firstly, a finite element analysis (FEA) model of the BLDCM is utilized to analyze the rotor eddy current loss caused by current harmonics with different pulse width modulation (PWM) switching frequencies. By selecting the optimal PWM switching frequency, it is possible to reduce rotor eddy current loss while minimizing switching loss. Furthermore, to address the drive loss resulting from non-ideal back EMF, this paper introduces a compound controller based on repetitive control. This controller incorporates the high-frequency PWM drive scheme, which helps reduce current fluctuations compared to the pulse amplitude modulation (PAM) drive scheme. As a result, the total power consumption of the high-speed motor is reduced by approximately 4.3% at the rated speed. Simulation and experimental results confirm the effectiveness of the proposed method.

engineering, electrical & electronic
A Simple Method for Modeling and Control of Brushless DC Motor

毕海悦,张东来,孙宝奎,任雷

2009-01-01

Abstract:Simple and direct modelling and the control method of brushless DC motor is the use online way seeking motor speed data,calculates the transfer function through the simulation,and carries on the PID control simulation.Finally taken experiment test of BLDCM,confirmed this method feasibility comparing the simulation result and the actual control result.
A Low Cost Hybrid Excitation Brushless DC Motor

付吉臻,郝鹤,沈建新,潘再平,梅营

DOI: https://doi.org/10.3969/j.issn.1001-6848.2009.08.010

2009-01-01

Abstract:Permanent magnet brushless DC motors(BLDCM)are widely used due to their merits such as free of commutation sparks,low EMI and maintenance-free.However,the high count of expensive power electronic devices in the drive circuit restricts the application of the BLDCM,particularly in those areas with low-cost demands,such as the application in cars.This paper proposed a hybrid excitation BLDCM,for which only two power electronic devices were used in the drive circuit.Presented the motor operation principle,and proved its performance satisfactory with simulation using finite element method and SPICE.
A New Method of Torque Ripple Minimization for Brushless DC Motors

WU Hao,SUN Xin-ya,JI Yin-dong

DOI: https://doi.org/10.15934/j.cnki.micromotors.2008.09.003

2008-01-01

Abstract:Proposed a new technique of suppressing the torque ripple in brushless DC motors(BLDCM) with trapezoidal-shaped back-EMF.Starting from the model of BLDCM,analyzed the factors influencing the electromagnetic torque,and applied optimal control on the stator currents to the torque ripple minimization.Extensive simulation results proved the superiority and simplicity of the proposed method in a wide range of speed,which was suitable for some high-performance applications.
Advanced Design And Operation Consideration For Close-Connected Winding Permanent-Magnet Brushless Dc Machine

Li Zhu,Shuangxia Niu,Y. C. Wang,Chengmin Wang

DOI: https://doi.org/10.1109/TASC.2016.2535969

IF: 1.9489

2016-01-01

IEEE Transactions on Applied Superconductivity

Abstract:Advanced design and operation consideration for the close-connected winding permanent-magnet brushless DC machine is proposed in this paper, including circulating current elimination, fault-tolerant control for the breakdown of a power electronic switch, and a sensorless control method. With the finite-element analysis, the influence of machine design parameters on circulating current is investigated. By properly controlling the status of power electronic switches, the coils being connected into the equivalent circuit can be changed to avoid the failure switch. Sensorless control is explored by detecting the zero-crossing point of electromotive force.
Drive of single-phase brushless DC motors based on torque analysis

Sun Lizhi,Feng Qi,Shang Jing

DOI: https://doi.org/10.1109/TMAG.2006.886965

IF: 1.848

2007-01-01

IEEE Transactions on Magnetics

Abstract:The high torque peaks commonly found in single-phase brushless dc motors can be compressed by different driving methods, which are proposed and studied based on finite-element analysis (FEA). It is concluded that one dead-zone can be added into the driving signals to improve current waveforms and torque envelope. The test results show that the noise level and performances are greatly improved when one proper dead zone is implemented. © 2006 IEEE.
Commutation Study of DC Motor for Automotive Fuel Pumps

韩韬,张亮

DOI: https://doi.org/10.3969/j.issn.1004-7018.2009.08.003

2009-01-01

Abstract:This paper described the significance of the commutation performance of the drive DC motor for the operation of the electric fuel pump,and analyzed the principle of the commutation process,especially the variation of commutation current.Considering the requirements of small size and constant load,a method to shift the brush for a small angle in the anti-rotation direction was proposed to solve the problem of commutation failure,which made electromotive force of commutation cell counteracted,as well as commutation and improved commutation.The test and simulation verifies that this method is valid and plain.

Study on Reducing Dead Area of the Brushless Direct Current Motor

Research on PWM Method in Brushless DC Motor

Study on Switching Strategy of PMSM and BLDCM

Reduction of Commutation Torque Ripple in Brushless DC Motors

Steady Performance Analysis on Single-Phase Brushless DC Motor

Simulation Brushless DC Motor and Driver with PSpice

A Novel PWM Scheme to Eliminate the Diode Freewheeling in the Inactive Phase in BLDC Motor

Comparative Performance Evaluation of Hall Effect Sensorless Control Options in Permanent Magnet Brushless DC Motor Drives

Study on Small Power BLDCM Drive System

Control Analysis of PM Brushless DC Motor Used in Flywheel Energy Storage System

New BLDCM Drive Method to Smooth the Torque

A Practical Method to Eliminate the Conduction Torque Ripple in BLDCM Using Cascade Topology

Dynamic characteristics analysis of the brushless DC motor direct drive system

A New BLDC Motor Drives Method Based on BUCK Converter for Torque Ripple Reduction

Low Power Consumption Control Method for BLDCM with Very Small Inductance and Nonideal Back EMF

A Simple Method for Modeling and Control of Brushless DC Motor

A Low Cost Hybrid Excitation Brushless DC Motor

A New Method of Torque Ripple Minimization for Brushless DC Motors

Advanced Design And Operation Consideration For Close-Connected Winding Permanent-Magnet Brushless Dc Machine

Drive of single-phase brushless DC motors based on torque analysis

Commutation Study of DC Motor for Automotive Fuel Pumps