Implementation of Inserting Data by Remultiplexer

王兴东,余松煜,梁龙飞

DOI: https://doi.org/10.3969/j.issn.1000-3428.2002.12.027

2002-01-01

Abstract:Design of transport stream (TS) remultiplexer is described in this paper. Some effective methods of data insertion based on CBR or VBR are proposed.

What problem does this paper attempt to address?

Implementation of MPEG-2 Transport Stream Remultiplexer for DTV Broadcasting

XD Wang,SY Yu,LF Liang

DOI: https://doi.org/10.1109/tce.2002.1010139

2002-01-01

IEEE Transactions on Consumer Electronics

Abstract:This paper presents the design and implementation of an MPEG-2 transport stream (TS) remultiplexer, which is one of the most important pieces of equipment in a digital television broadcasting system. To achieve high performance as well as save hardware resources, the architecture of CAM+RAM is proposed to substitute simple RAM where a PID information table is generated. Compared to other methods, the two-step PCR correction approach can simplify the system significantly. Three data insertion modes are discussed in this paper. Among of them, the host-downloading architecture supports the system to work in a standalone mode when the contents of data are repeated with a fixed time interval or change not very fast.
Design and implementation of a multi-programs transport stream multiplexer

Lei Zhang,Xiaofeng Huang,Yangang Cai,Zhuo Li,Huizhu Jia,Xiaodong Xie

DOI: https://doi.org/10.1109/InfoSEEE.2014.6947842

2014-01-01

Abstract:This paper describes design and implementation of a multi-programs transport stream multiplexer which is based on AVS system standard. We have developed an AVS TS compliant multiplexer with special considerations for multi-programs multiplexing. In particular, we construct a monitoring structure which can imitate the behavioral model of T-STD and then use the monitoring information as the key factors for scheduling. We have made efficient verification of AVS and MPEG-2 compliance by RTL simulation.
Implementation Technology of HDTV Transport Multiplexer

Jun Li,Wei Ye,Tian Huang,Songyu Yu

DOI: https://doi.org/10.3321/j.issn:1006-2467.1999.01.032

1999-01-01

Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University

Abstract:The real time implementation designing method and the implementation technology of an HDTV transport multiplexer were given based on the discussion about MPEG-2 transport layer syntax. The function of a transport multiplexer was to package the audio, video and auxiliary data to TS packets according to MPEG-2 transport layer syntax, and to transmit those packets to a channel. The main idea of transport multiplexer designing method was checking the status of every input buffers of a multiplexer by using a SDP and packaging the data read from buffers to the TS packets according to the buffer status. Each kind of the TS packets can be interlaced equally by using this method. The implementation result was also given.
Software Implementation of Transport Stream Multiplexer Based on IP

XIONG Lei,YU Hongyang,ZHANG Ping

DOI: https://doi.org/10.3969/j.issn.1002-8692.2011.02.016

2011-01-01

Abstract:Taking TS stream based on IP as a research object,the implementation of TS stream transmitting in IP networks,the extraction and rebuilding of programe special information as well as the adjustment of programe clock reference,which are the two key technologies in TS multiplexing are analysed,a method of software implementation for real-time multiplexing of Transport Stream is proposed,which transmit in IP networks.Finally,the design and software implementation of multiplexer are accomplished on Linux platform with the correct testing results.
Design and implementation of twin transport stream demultiplexor in HDTV decoder

Zhu Zheng,Zhu Mengyao,Wang Lianghao,Luo Kai,Huang Zhijie,Ming Zhang

DOI: https://doi.org/10.1109/ICASIC.2007.4415734

2007-01-01

Abstract:A new architecture for transport stream demultiplexer (TS Demux) in high definition television (HDTV) decoder is presented in this paper, which is able to demultiplex two TS inputs synchronously. We have pursued a hardware-based design that controlled by the software to yield high performance in the least silicon area. The key parts of the architecture, including PID filter, section filter and Memory Control Unit (MCU), are shared by the two TS inputs in terms of a time slice. Owing to the elaborate shared mechanism, our design is efficient to support more tremendous functions with less resource compared to the current scheme.
A CATV Oriented Reliable Multicast File Transfer System

TAO Zhenjiang,XING Wei,LU Dongming

DOI: https://doi.org/10.3969/j.issn.1000-3428.2006.05.042

2006-01-01

Abstract:This paper presents a CATV based multicast file transfer system on top of ALC reliable multicast protocol,and also adjusts the work parameters of this system according to the characteristic of CATV.Based on this system,PC users can experience reliable file downloading at high speed with QoS assurance by access to the CATV network using DVB network interface.The system has already been implemented and successfully applied in practice.
Implementation of TS Streams Pack/unpack and Transport in DSP.

Yingchao Han,Hongmei Li,Jinghui Qiu

DOI: https://doi.org/10.1109/emeit.2011.6023234

2011-01-01

Abstract:In this paper, a video wireless transmission system based on DVB-T is introduced with the DM642. Based on this system, the packing-unpacking TS stream device is designed in DSP, and the method to output TS stream by means of using EDMA, GPIO and serial peripheral interface (SPI) is proposed. This method which has been proved is an effective solution to transport TS streams. It is not only reduces the cost but also reaches the industrial temperature level standards.
Design and Implementation of Transport Stream Demultiplexer in HDTV Decoder SoC

CR Zhang,SB Zheng,F Wang,C Yuan

DOI: https://doi.org/10.1109/tce.2005.1468013

2005-01-01

IEEE Transactions on Consumer Electronics

Abstract:A novel architecture of transport stream demultiplexer (TS Demux) in high definition television (HDTV) decoder is presented in this paper, which utilizes a cooperation scheme between hardware and software. TS parsing is decomposed into two phases: filtering and analyzing, which are fulfilled by hardware and software respectively. Meanwhile, the hardware filtering is controlled by the software. Two filtering layers, PID and section filtering, are supported by hardware, which can extract any format data in TS stream quickly. Compared to the current parsing scheme for TS packets, TS Demux discussed here needs less CPU resource and is easy to update as well.
System Design for De&Re-multiplexing of MPEG-2 Transport Stream Based on DM642

LU Guo-xun,SUN Jun,ZHOU Jun

DOI: https://doi.org/10.3969/j.issn.1006-8961.2006.11.024

2006-01-01

Journal of Image and Graphics

Abstract:To achieve high performance and simplify the design,this paper presents the system design for dere-multiplexing of MPEG-2 TS(transport stream) based on DM642.Compared to former methods,this design uses many DM642 internal hardware properties such as Video Port,PCI(peripheral component interconnect),EDMA(enhanced direct memory access) etc,by which the system performance is enhanced.The algorithm of PCR(program clock reference) correction based on VIC Port(voltage controlled crystal oscillator interpolated control port) is proposed which reduces the complexity of PCR correction.Experiments have proved that the max TS processing rate is 80 Mbps,which meets the application requirements.
Application and Implementation of Multicast Technology in Real-time Video Ttansfer System

单喆,魏明亮,陈道蓄,谢立

DOI: https://doi.org/10.3969/j.issn.1002-137X.2000.11.005

2000-01-01

Computer Science

Abstract:In this paper we study the key issues of the real-time video transfer system when applying multicast technology.First we introduce an application-level high-performance multicast transport protocol RTMTP to offer guarantees of real-time and stable video transmission.Second,we improve the management of flow control by adding the component Video Repeater,avoiding the traditional way in which centralized and inflexible methods are applied.Third,packet forwarding is achieved through hierarchical service control of Repeaters.Finally,the implementation of a solution is issued and the performance of a sample system based on it is tested.
Statistical Multiplexing Model in the Packet Switching Network and Algorithms Implemented on CATV Network

赵忠伟,李式巨

DOI: https://doi.org/10.3785/j.issn.1008-973x.2004.02.004

2004-01-01

Abstract:A statistical multiplexing model in the packet switching networks was presented through closed form evaluation of relevant parameters characterizing the process at the output packet sequences of the multiplexer. Compared with previous approaches, the proposed method evaluated the efficiency of the multiplexing process through the autocorrelation function and the mean length of adjacent packet sequences, and also determined the I/O buffer of multiplexer. The author used this model to design and implement an MPEG-2 TS multiplexer on CATV network. In this multiplexer, author presented Periodic Verification and Check Out algorithm to ensure bit rate and proposed Dynamic Space Array algorithm to adjust PCR for every stream. Eventually, the result from real-time system shows the efficiency of these algorithms.
Virtual Buffer Control Strategy for MPEG-2 System Layer Multiplexing

Bo Pu,Jun Sun,Songyu Yu

DOI: https://doi.org/10.3321/j.issn:1006-2467.1999.01.020

1999-01-01

Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University

Abstract:It described single program transport stream multiplexing of MPEG-2 system layer, analysed conditions defined in T-STD model that the transport stream should satisfy, and then proposed single program transport stream multiplexing algorithm based on virtual buffer status. In the algorithm, a virtual system layer T-STD was established to produce a feedback cycle with multiplexer. The multiplexer was feed backward controlled by the T-STD buffer fullness to ensure that the transport stream had rational construction and met the criterion which did not make the T-STD buffer to either overflow or underflow. The experimental results show that the interleave constructions of transport stream packets are uniform and rational.
The Implementation of LAN VOD System with IP Multicast

林铸祥,张朝阳,王曰海,陈文正

DOI: https://doi.org/10.3969/j.issn.1001-3695.2002.06.048

2002-01-01

Abstract:This article focuses on the implementation of LAN VOD (Local Area Network Video On Demand) system with IP Multicast. The IP Multicast and its implementation are discussed in the first part, and a scheme to provide interactivity with SRMDRU is introduced in the second part. At the end of this article the result and performance of the system are reported.
Embedded Transmission of Multi-Service Over DTMB System

Xiaoqing Wang,Jintao Wang,Jun Wang,Yangang Li,Shigang Tang,Jian Song

DOI: https://doi.org/10.1109/TBC.2010.2067550

2010-01-01

Abstract:To efficiently support the transmission of terrestrial and mobile services within the same spectrum over the Digital Television Terrestrial Multimedia Broadcasting (DTMB) system, a flexible multi-service datacasting scheme in a backward compatible manner is proposed. Using this scheme, the conventional DTMB receivers work as usual by simply selecting the specific terrestrial DTV programs on the basis of the package identifier (PID) checking, while only the desired mobile service data are processed by the mobile receivers via the designed control signals. Both theoretical analysis and computer simulation show that, at acceptable spectral efficiency penalty, the proposed method not only supports the embedded transmission of multi-services with no reception performance degradation for the traditional terrestrial broadcasting service, but also flexibly provides much better mobile reception performance.
Design and Implementation of the Streaming Media Transport System Based on RTP

Xin-yong PANG,Rui-fang MA,Ping-fen LIU,Wen-ge YANG

DOI: https://doi.org/10.3969/j.issn.1000-7180.2007.11.054

2007-01-01

Abstract:This paper proposes to solve the problems of real-time transport efficiency and scalability of the system. Based on careful analysis to RTP protocol, a streaming media transport model is designed, which aims at the special requirement in real-time transport; also many key issues are studied deeply, for example, flow control, packet composing algorithm and buffer management. Finally, the detailed implementation of the system is given.
Multiplexing Video Traffic Using Frame-skipping Aggregation Technique.

A Yeung,SC Liew

DOI: https://doi.org/10.1109/icip.1997.647774

1997-01-01

Abstract:MPEG is a popular compression standard used in many multimedia applications. In video distribution systems, a CBR communications channel is often shared among several VBR MPEG video streams. Since there are fluctuations of data rates in video streams, traffic congestion may occur and video quality may be affected. We propose a frame-skipping aggregation technique to multiplex several MPEG streams (outside the network) to feed into a CBR channel (within the network). The salient feature of the scheme is that the transmission of bi-directionally predicted frames will be slipped (outside the network) before the onset of traffic congestion so as to minimize the image quality degradation. Our result shows that using this technique, more users can be supported compared to regular video transmission systems. This technique allows us to adopt a simple call admission strategy in which video requests are granted based on their mean rates
Design and Implementation of Multiplexing Rate Control in Broadband Access Network TV Transmission System.

HK Xiong,J Sun,SY Yu,CF Luo,J Zhou

DOI: https://doi.org/10.1109/tce.2004.1341690

2004-01-01

IEEE Transactions on Consumer Electronics

Abstract:This paper addresses the implementation architecture and protocol procedure of the dedicated broadband access network TV transmission system. According to application-oriented quality of service (QoS), two alternative rate control schemes for multiple DTV programs transmission are proposed collaborating with MPEG-2 system strategy and IP-base network multiplexing mechanism. As to the network bandwidth utilization, a flexible RTF-based synchronization resilience scheme for VBR transport stream (TS) transmission is realized to ensure the performance requirement for MPEG-2 standard. As to the MPEG-2 system strategy, moreover, a parallel VBR transcoding/encoding rate control algorithm for CBR TS transmission could achieve a consistent picture quality for multiple DTV programs under a constrained fixed-rate network bandwidth. For adapting the variable access network bandwidth, the system main control module can flexibly schedule the available rate control scheme for multiple slave service multiplexers. Experimental results demonstrate that the proposed schemes not only improve the traditional TV broadcast adaptation to Internet, but also achieve a more ideal program picture quality constrained by multi-program parallel multiplexing.
Permutation-Based Transmissions in Finite Blocklength Regime: Efficient and Effective Resource Utilization

Wenyao Li,Yuli Yang,Bingli Jiao

DOI: https://doi.org/10.1109/TCOMM.2023.3253698

IF: 6.166

2023-01-01

IEEE Transactions on Communications

Abstract:In this paper, the concept of permutation-based transmissions is developed at the transport layer of short-packet communications, where the application-layer data is divided into two parts: one is conveyed by the permutation of various lengths in a group of packets, and the other is encapsulated into these various-length packets. The former part, referred to as permutation-conveyed data unit (PCDU), improves the goodput and reduces the latency. From a finite blocklength perspective, the maximal payload rate of permutation-based transmissions is formulated, based on which the goodput and latency are derived and obtained in analytical forms. Moreover, the spectral efficiency and energy efficiency are analysed. Illustrative numerical results on the performance and resource utilisation comparisons not only substantiate the advantages of our permutation-based transmissions over conventional transport-layer encapsulation schemes, but also provide useful tools and specifications for the PCDU design in short-packet communications.
Using Object Multiplex Technique in Data Broadcast on Digital CATV Channel

ZQ Gu,SY Yu,WJ Zhang

DOI: https://doi.org/10.1109/tbc.2004.828365

IF: 4.5

2004-01-01

IEEE Transactions on Broadcasting

Abstract:Data broadcast is a new kind of value-add service of DTV broadcasting and some data broadcast protocols have already been established. However, these protocols only describe the method for locating files in data streams, method on how to distribute large collection of files in one or more data streams is not provided. Research on this problem mainly focus on how to decrease the wait time and some methods of allocating files on multiple streams based on access probability are proposed, but how to assign the file with a reasonable bandwidth is ignored. In this paper, we introduced an object multiplex algorithm to optimize the allocation of objects on DTV channel. This method assigns different bandwidth statistically to different object according to its size and access probability. In this method, both download time and wait time are considered. It adopts a modified Virtual Clock (VC) scheduling algorithm to multiplex files accurately and smoothly.
Study of MPEG-2 TS Multiplexer Based on Software Realization

Xinan Zhang

2007-01-01

Abstract:This paper mainly introduces system structure of the TS multiplexing software in the MPEG-2 TS multiplexer based on software realization, extraction of the information in many kinds of TS flow, and synthesis of program specific information (PSI). At the same time, the paper gives a major introduction of multi-thread program and correction of program clock reference (PCR) in the process of software reclamation.

Implementation of Inserting Data by Remultiplexer

Implementation of MPEG-2 Transport Stream Remultiplexer for DTV Broadcasting

Design and implementation of a multi-programs transport stream multiplexer

Implementation Technology of HDTV Transport Multiplexer

Software Implementation of Transport Stream Multiplexer Based on IP

Design and implementation of twin transport stream demultiplexor in HDTV decoder

A CATV Oriented Reliable Multicast File Transfer System

Implementation of TS Streams Pack/unpack and Transport in DSP.

Design and Implementation of Transport Stream Demultiplexer in HDTV Decoder SoC

System Design for De&Re-multiplexing of MPEG-2 Transport Stream Based on DM642

Application and Implementation of Multicast Technology in Real-time Video Ttansfer System

Statistical Multiplexing Model in the Packet Switching Network and Algorithms Implemented on CATV Network

Virtual Buffer Control Strategy for MPEG-2 System Layer Multiplexing

The Implementation of LAN VOD System with IP Multicast

Embedded Transmission of Multi-Service Over DTMB System

Design and Implementation of the Streaming Media Transport System Based on RTP

Multiplexing Video Traffic Using Frame-skipping Aggregation Technique.

Design and Implementation of Multiplexing Rate Control in Broadband Access Network TV Transmission System.

Permutation-Based Transmissions in Finite Blocklength Regime: Efficient and Effective Resource Utilization

Using Object Multiplex Technique in Data Broadcast on Digital CATV Channel

Study of MPEG-2 TS Multiplexer Based on Software Realization