Design of Motion Controlling Cards Based on PCI Bus

魏仁选,周祖德

DOI: https://doi.org/10.3969/j.issn.1000-3428.2004.08.068

2004-01-01

Abstract:A motion controlling card based on PCI bus is developed with FIFO buffers. The card can accomplish high-rate, bidirectional, parallel communication between controlling card and host computer. The design of hardware and software is discussed. The communication mechanism is provided in detail.

What problem does this paper attempt to address?

Design of Motion Control System Based on PC and Motion Control Card

Qingyong ZHANG,Danhong ZHANG,Wen JIANG

DOI: https://doi.org/10.3963/j.issn.2095-3852.2015.06.038

2015-01-01

Abstract:Firstly, motion control system structure based on PC and movement control card was introduced .Then the realiza-tion of interface controller between PCI bus and special motion control chip by use of interface chip PCI 9054 and programmable logic device FPGA was mainly described .The interface controller also implements the direct communication between FPGA and PCI9054 to expand the function of PCL6143, which makes the motion control system more open -ended.The maximal theoretical communication rate is up to 140MB/s.
Design of Motion Control Card Hardware Based on PCI

Li Wengang,Liang Chuhua,Zhou Jianping

DOI: https://doi.org/10.3969/j.issn.1672-8904.2010.03.013

2010-01-01

Abstract:Open CNC System, as present-day direction of the mainstream of development of the CNC technology has been a wide range of applications and development. At present, the motion control card based design based on the ISA bus, The bus transfer rate can not meet the industrial demands gradually. C8051F020 for this article will be CPU, based on the PCI bus introduced the motion control card system design.
Design of Motion Control Board Based on CPCI Bus

卫巍,张为公,何莉

DOI: https://doi.org/10.3969/j.issn.1004-373x.2008.14.026

2008-01-01

Abstract:According to requirement of high reliability in motion control system,a design of hot swap motion control board based on CPCI bus is presented in this paper.The card uses advanced technology to ensure high speed,reliable transmission system and a hot swap function allowing the system more convenient in the usage and maintenance.The hardware is consti-tuted of three parts:CPCI bus interface,hot-swap controllers and motion control circuit.The driver is programmed by WinDriver.This motion control card has been used in vehicle driver robot,final result indicates that the card runs stability,is easy to operate and has wide application prospects.
Design and Implementation of High-Speed Real-Time Communication Architecture for PC-Based Motion Control System.

Jian Hu,Hui Wang,Chao Liu,Jianhua Wu,Zhenhua Xiong

DOI: https://doi.org/10.1007/978-3-319-13963-0_41

2014-01-01

Abstract:To enhance the efficiency and stability of real-time data acquisition and transmission in motion control process, a high-speed real-time communication architecture based on FPGA and DSP is developed in this paper. The direct-memory-access (DMA) control module initiates DMA transfers over the peripheral-component-interconnect (PCI) bus. After that, two first-in-first-out (FIFO) buffers work as caches and convert data widths between the PCI bus and the local bus. Consequently, the data caches can be accessed by DSP over the local bus under DMA mode. The size of data transferred each time is able to be adjusted according to the application requirements. Experiments are carried out to demonstrate that the proposed communication architecture is capable of achieving high speed and stability in data communication with low consumption of compute resources.
Design of Motion Control Card Based on CPCI Bus and Its Driver in VxWorks

HE Li,GONG Zong-yang,ZHANG Wei-gong,WEI Wei

DOI: https://doi.org/10.3969/j.issn.1000-8829.2008.08.015

2008-01-01

Abstract:According to requirements of real-time and reliability of the system in motion control of vehicle unmanned robot system,a motion control card based on CPCI Bus is developed and its driver design in VxWorks is introduced in detail.The test results indicate:the motion control card and its driver can operate normally and stably and the system meets well requirements for motion control in vehicle unmanned robot system.At the same time,the foreground of application is broad.
PCI Bus-Based WDM Device Driver for Motor Control Board

王磊,朱齐丹,王亮

DOI: https://doi.org/10.3969/j.issn.1003-7241.2003.06.014

2003-01-01

Abstract:As a prevalent technology,PCI bus protocol has many advantages and is widely used.This paper presents the design of WDM device driver for device based on PCI bus by introducing design of exact motor motion control board based on PCI bus.It elaborates capture of PCI device,read and write of I/O port,read and write of memory and manage of interrupt.At last the installation of WDM device driver is shown.
The Design of Intelligent 429 Bus Interface Card Based on Dual-Port RAM

Shao-hua LIU,Jian-guo YAN,Ge-qun LIU

DOI: https://doi.org/10.3969/j.issn.1674-5795.2005.01.015

2005-01-01

Abstract:In the design of the intelligent 429 bus interface card,a single chip processor and a dual-port RAM are used.The card can deal with the communication data automatically and quickly.Using the dual-port RAM as a single chip and ISA bus data mutual media,the transmission velocity is improved. The address space allocation of dual-port RAM and a share conflict arbitration are discussed.The software of interface card is introduced. Its results show that it has advantage of high velocity and good reliability.
Design and implementation of digital signal source based on PCI

郑琨,王英民,张争气

DOI: https://doi.org/10.16208/j.issn1000-7024.2008.19.007

2008-01-01

Abstract:During the course of digital communication system and processing system manipulation,a high-speed and real-time signal source is needed.Through the example of serial transmission,the technique of high-speed signal source based on PCI bus is discussed.The signal data is given by general computer and transmitted in serial via PCI bus.The receiving hardware system need not be modified.Finally,through the hardware design,the device driver programming and the control of programmable logical unit,the particulars of the design and implement methods are introduced.
Design of Multi-axes Control System Based on PCMC Card

LI Jian-jun,ZHANG Kai-long,YANG Zhi-yi,LIANG Ke

DOI: https://doi.org/10.3969/j.issn.1001-2257.2006.07.007

2006-01-01

Abstract:A motioncontrol architecture of EPMCC,which is based on embedded platform and PCMC card,is presented,moreover,the multiaxes cooperative control method is illustrated.The principle and crucial technique of building hardware platform and developing software is emphasized by taking the electropatternsewing machine for example.
Design of Controlling Card Based on PCI Bus for Digital Tube Field Display

FU Zuo-wei,FU Xing,ZHONG Ru-jun,CHEN Zhi,BAI Mao-sen

DOI: https://doi.org/10.3969/j.issn.1007-2780.2010.02.016

2010-01-01

Chinese Journal of Liquid Crystals and Displays

Abstract:The PCI local bus is an advanced and high performance 32/64 bit bus with multiplexed address and data lines,which is easy to realize I/O controlling card or communication interface card under high-speed and real-time. A PCI bus controlling card based on CH365 chip is designed in this article. The card mainly consists of PCI interface chip,MCU and data buffer. At the same time,display circuit based on driver chip CH451 is designed,the circuit connected control signal of MCU. It can realize data display with fewer pins as several CH451 chips are applied by parallel connected. The experiments proved that field display is feasible based on PCI bus controlling.
The Design Procedure of Computer PCI Bus Device

张勇,赵刚

DOI: https://doi.org/10.3969/j.issn.1003-5850.2006.10.014

2006-01-01

Abstract:For transferring data at high speed between computer and peripheral devices,this paper presents the design of an extended device based on the peripheral component interconnect(PCI) bus,which implements the whole process that exchanges data between the computer and the peripheral devices via PCI bus,and process data in the VC++ high-level programming language environment.Nowadays this method has been widely applied to the different areas.
Programmable Logic Design on PCI9054 Local Bus Control

彭杰,汪国有,张天序

DOI: https://doi.org/10.3969/j.issn.1006-9348.2003.09.025

2003-01-01

Abstract:PCI bus is high bandwidth, being independent of CPU, high capacity bus. The bus interface controller design is its key techniques to application .In this paper, the PCI9054 interface controller is introduced, the PCI9054 local bus interface controller is designed with programmable logic. According to the design, the data transformation and communication between PCI9054 local bus and local bus device are realized easily.
Design and Implementation of FPGA Based High-Speed Bus for Control System

MI Xiao-ling,HUANG Wen-jun,JIN Jian-xiang,SHI Yi-ming

DOI: https://doi.org/10.3785/j.issn.1008-973x.2011.11.026

2011-01-01

Abstract:The system architecture of high-speed bus was studied to improve the control system communication speed and efficiency.A FPGA based high-speed bus applied in control system was designed and implemented,which is high real-time,high throughput,easy to expand and so on.The physical layer was based on multipoint-low-voltage differential signaling(M-LVDS) standard to achieve 256 Mbps serial communication.Multi-path optimization selection network redundancy through real-time link state maintenance was used in data link layer to ensure reliable communications while maximizing bandwidth utilization.The design was implemented on Xilinx XC3S400A FPGA and actual tests were done.Results show that communication speed and real-time performance are improved significantly compared with the current mainstream bus of control system,and the needs of upper applications are met to the greatest degree.
Design and Implementation of PCI-based Control System for Gravure Engraving Machine

LIU Liang,ZHOU Zhao-yao,HE Ke-jing,QIN Xue-feng

DOI: https://doi.org/10.3969/j.issn.1001-3997.2011.10.007

2011-01-01

Abstract:A method for designing the PCI bus using VerilogHDL was studied.To satisfy the requirements of large-scale image data transmission,a multi-axes motion control system based on PCI bus was proposed and the simplified PCI functions were realized in altera's cyclone chips and timing sequence was simulated by ModelSim.Then FPGA was employed as the main controller in this control system and an algorithm of acceleration and deceleration was designed specific to the engraving machine system to ensure the high-speed and high-precision control.Finally,the system was applied to high speed gravure engraving machine to verify the design through experiments.
Implementation of an interface card of a position control system based on PCI bus

Wang Peng,Dong Jingxin,Zhao Changde

DOI: https://doi.org/10.3969/j.issn.1002-4956.2010.05.029

2010-01-01

Abstract:For the purpose of making students handle the technology of computer controlling,an interface card is designed with PCI9054,which is used in the Computer Controlling System class.The card includes interface to PCI(peripheral component interconnect) bus,sample pulse generator,counter of position,D/A,etc.It can support students to realize kinds of controlling method through programming on computer,to solidify the knowledge of computer controlling.
Hardware Design and Realization of ARINC429 Bus Interface Board Based on PCI Bus

Shi Guoqing,Gao Xiaoguang,Wu Yong,Zhang Jiandong

DOI: https://doi.org/10.16526/j.cnki.11-4762/tp.2010.01.028

2010-01-01

Abstract:A hardware design and realization of multi-channel intelligent ARINC429 bus interface board based on PCI bus is introduced.In the design,using PLX's PCI9052 as a PCI bus interface chip,using TI's TMS320F2812 as the embedded CPU of the interface board,combined with Device Engineering Corporation's DEI1016 and BD429 chips as ARINC429 bus interface,using Altera Corporation's FPGA chip EP1C12 to realize the address decoder,logic control functions of the interface board.This circuit design simplifies the PCI interface circuit design of the interface board,effectively improves the executing speed of the interface board,while it has the virtue of high integration,small size,communication channels can be changed etc.The interface board has been used in numbers of application projects,the experiment in which proved its good stability and high performance.
Design of PCI Bus General 6-Axis Motion Controller Based on DSP

GAO Yun-feng,JIANG Hua

DOI: https://doi.org/10.3969/j.issn.1001-2265.2005.10.012

2005-01-01

Abstract:In this article,to carry the 6-axis motion controller out,a method of using PCI special interface chip PCI9052 to be a interface bridge of PCI bus and DSP(TMS320LF2407),was introduced.Firstly,the whole hardware structure of the controller was given,including the interface specification of PCI bus,local bus interface circuit,DSP expander.Secondly,the collocation method of the board was introduced,thus the configuration of address rage register,base register and chip selection control register was involved.Finally,this article presented the design method of the driver program.Throughthis method of combining PCI and DSP,we can carry out the fast communication between controller and upper controller and take the full advantage of the DSP's features of high-speed and powerful.
A Design of PCI-bus High Speed Serial Communication Card

Yu Peng,Yanmeng Ba,Bo Li

DOI: https://doi.org/10.1109/icemi.2009.5273990

2009-01-01

Abstract:This paper proposes a design of PCI bus high speed LVDS communication card, which can be widely applied in high speed serial communication of PCI-based electrical systems. The LVDS standard is deployed as front-end communication interface to implement a 120 Mbps serial communication speed within 10 meter communication distance. To promote data transaction efficiency on the PCI bus, we propose a high efficiency DMA data transition method. In the proposed DMA method, to promote PCI bus communication efficiency, we adopt continuous burst to increase the bus efficiency. Furthermore, we adopt common buffer DMA to ensure data transaction continuity. A generic method on developing WDM driver for PCI devices is also presented at the end of the paper. Comprehensive measurement experiment reflects that the PCI hardware transaction speed in this design can reach more than 120 Mbytes/second, which is highly efficient and meaningful for high speed data communication or applications alike.
Design of High Speed Data Transmission System Based on CPCI Bus and LVDS

Li Jin,Jiao Xinquan,Liu Donghai,Wang Shuqin

DOI: https://doi.org/10.16157/j.issn.0258-7998.183275

2019-01-01

Abstract:In order to accurately receive and process large-capacity high-speed data in real time，based on the in-depth study of CPCI Bus，a high-speed data transmission system based on CPCI Bus and LVDS is proposed. PCI9054 is used as the bridge device and FPGA is the microcontroller. The transmission mode combining PCI Target single-cycle mode read/write instruction and DMA burst mode transmission data is designed to improve the data transmission speed while ensuring reliable data transmission.After practice testing，the design work is stable，the transmission is accurate，and the expected transmission task is successfully completed.
Research on Laser Marking Control System Based on PCI Bus

蒋毅,蒋明

DOI: https://doi.org/10.3969/j.issn.1004-373x.2009.06.005

2009-01-01

Abstract:A design of laser marking control system based on PCI bus is introduced in this paper.PLX PCI9052 chip is used for PCI interface design and Altera CPLD device EPM7064 is used for logical controlling of bus coding and functional circuit.With AHDL programming language,IP soft core is designed to acquire precisely PWM signal output to control laser power.Test software is designed for improving the control card design and laser marking software expand its applications.

Design of Motion Controlling Cards Based on PCI Bus

Design of Motion Control System Based on PC and Motion Control Card

Design of Motion Control Card Hardware Based on PCI

Design of Motion Control Board Based on CPCI Bus

Design and Implementation of High-Speed Real-Time Communication Architecture for PC-Based Motion Control System.

Design of Motion Control Card Based on CPCI Bus and Its Driver in VxWorks

PCI Bus-Based WDM Device Driver for Motor Control Board

The Design of Intelligent 429 Bus Interface Card Based on Dual-Port RAM

Design and implementation of digital signal source based on PCI

Design of Multi-axes Control System Based on PCMC Card

Design of Controlling Card Based on PCI Bus for Digital Tube Field Display

The Design Procedure of Computer PCI Bus Device

Programmable Logic Design on PCI9054 Local Bus Control

Design and Implementation of FPGA Based High-Speed Bus for Control System

Design and Implementation of PCI-based Control System for Gravure Engraving Machine

Implementation of an interface card of a position control system based on PCI bus

Hardware Design and Realization of ARINC429 Bus Interface Board Based on PCI Bus

Design of PCI Bus General 6-Axis Motion Controller Based on DSP

A Design of PCI-bus High Speed Serial Communication Card

Design of High Speed Data Transmission System Based on CPCI Bus and LVDS

Research on Laser Marking Control System Based on PCI Bus