Characteristics and application of surface wave propagation in fluid-filled porous media

Zhang Yu,Xu Yi-Xian,Xia Jiang-Hai,Zhang Shuang-Xi,Ping Ping

DOI: https://doi.org/10.6038/cjg20150812

2015-01-01

Abstract:High frequency surface wave method based on seismic wave propagation in single-phase media has been widely applied for acquiring near surface shear wave velocity in several fields. However, the near surface earth media, consolidated and unconsolidated, for the general hydrogeological conditions, bear plenty of pores. Fluid in pores affects the surface wave propagation in the media remarkably, which is represented in dispersion in velocity and attenuation. The pore fluid behaviors through the free surface make the boundary more complex as fully drained, fully sealed and partially drained conditions. These effects are taken into account in surface wave secular equation derivation and closed-form dynamic response investigation. Complex searching algorithm and fast coverage quadrature are applied in the dispersion and response calculation. Typical near surface earth media are selected. For weakly consolidated media in which the surface wave propagates in an extremely low velocity, the effects of the motion of source are obtained. The partial saturation of mesoscopic loss significant in seismic frequency band is introduced beyond the Biot model. The effective viscoelastic model that has been used for body waves in porous media is extended to solve the boundary value problem of surface wave propagation by coupling body wave representations on the free surface. For one fluid saturated, R1 mode wave can propagate under each boundary condition, which is similar with classic Rayleigh wave in elastic media. Its phase velocity is a little less than the S wave and amplitude is strong in seismograms. Due to the intrinsic attenuation, R1 wave is dispersive in the homogeneous half space. The velocities and attenuation coefficients are different under different fluid boundary conditions. Biot solid-fluid coupling coefficient controls the critical frequency of dispersion as for the body waves. High solid-fluid coupling can eliminate the differences. Tortuosity affects R1 waves for different fluid boundaries with different sensitivities. R2 mode appears and propagates under sealed and partially drained conditions. Its phase velocity is a little less than P2 wave. In most cases, it is difficult to be observed in dynamic responses. However, when the solid-fluid coupling is low, it may obtain the radiation from R1 wave as a non-physical wave with strong amplitude under partially drained surface. When the velocity of surface wave is low in weak media, the movement of source impulse with regards to the receiver makes remarkable effects on surface wave responses. Radical velocity to the receiver makes Doppler frequency shift. Lateral velocity makes distortions of wave responses in time and frequency domains. For partial saturation with heterogeneous multiphase fluid saturated patches, the mesoscopic flow induced by wave can interpreter wave attenuation in seismic frequency band, which is accordance with the practical data. Because the fast P1 wave is dominantly affected by this strong loss mechanism, R1 wave is more distinctively related to P1 wave considering partial saturation, quite different to the Biot fluid saturated model. The critical frequency for mesoscopic mechanism is controlled by fluid compositions in the patches, which in turn presents the correlation for surface wave signals to subsurface fluid distribution and flowing. Because the Biot critical frequency is always high, standard linear viscoelastic solid can effectively represent R1 wave propagation in porous media in seismic frequency band by the coupling body wave fits and ignoring the slow wave perturbation, especially for the dynamic responses in the time domain. While in patchy saturation model, the P wave propagates under the interactive wave induced flow between the two P wave modes, which also make it simple to effectively represent. The fluid phase in near surface media can be regarded as an important factor for surface wave data acquisition and processing. The effects of different fluid free surfaces need to be considered for correction in several unconsolidated and high permeability rocks. The low velocity of the surface wave makes the movement of source be an important impact in the frequency responses. For passive surface wave observation usually with low frequency signal extraction, this impact needs to be carefully estimated. The dominated mesoscopic mechanism in seismic frequency band shows obvious attenuation in the P wave, which also dominates the surface wave propagation. For near surface attenuation estimation by surface wave, the P wave must be paid attention to. The developed effective medium saves the storage and time consumption for surface wave in porous media, which can be applied in the inversion modeling for surface wave image in an economic way.