Abstract:The reaction between the hydroxyl groups on the surface of acid-treated multi-walled carbon nanotubes (MWNT) and 2-bromo-2-methylpropanoyl bromide generates ATRP initiator sites on the MWNT, and then fluorinated acrylates were polymerized from MWNT via a "graft-from" method. Fourier transform infrared spectrometry (FT-IR), transmission electron microscopy (TEM) and thermogravimetric analysis (TGA) results indicate that the polymer was covalently attached or grafted to the Surface of MWNT. Using MWNT coated with low surface energy polymer as the filler particles, a solution-casting method was employed to prepare MWNT/polyurethane composite films. The surface of composite films was exposed to tetrahydrofuran (THF) as the etchant to obtain the rough surface with microstructures. Static contact angle tests showed the hydrophobic properties of films were enhanced by adding the MWNT, and the contact angle was increased with the content of MWNT. The MWNT grafted with fluorinated polymers showed better hydrophobic performance than the pristine MWNT at the same content, and the film hydrophobicity was greatly improved after etching by solvent. Scanning electron microscopy (SEM) was used to study the microstructures of surfaces of composite films before and after etching. Effect of MWNT on the hydrophobic properties of the composite film surfaces was in-depth studied. Our experiments demonstrated that the hydrophobic properties of MWNT surfaces could be tuned via functionalization using different surface energy materials and the fabrication of polyurethane composite films with hydrophobic surfaces could be successfully achieved.

Preparation of Mumti-wall Carbon Nanotubes (mwnts )/acrylate Composite Latex

Nanocomposites of Poly(vinylidene Fluoride) with Multiwalled Carbon Nanotubes

Preparation of Cellulose/MWCNTs/TPU Micro-foam Composites

Liquid Crystalline Pet/60hba-Mwnts Composite: Synthesis, Characterization, and Properties

Preparation of Isotactic Polypropylene-Grafted Multiwalled Carbon Nanotubes (Ipp-G-mwnts) by Macroradical Addition in Solution and the Properties of Ipp-G-Mwnts/Ipp Composites

Exfoliated PS/MMT nanocomposites prepared by emulsion polymerization

Fluorinated Multi-Walled Carbon Nanotubes and Fabrication of Polyurethane Composite Films with Hydrophobic Surface

Preparation and Properties of the Polyimide/multi-Walled Carbon Nanotubes (mwnts) Nanocomposites

Effect of the Surface Functionalization of Graphene and MWCNT on the Thermodynamic, Mechanical and Electrical Properties of the Graphene/MWCNT-PVDF Nanocomposites

The cutting of MWNTs using gamma radiation in the presence of dilute sulfuric acid

Hydrothermal treatment to prepare hydroxyl group modified multi-walled carbon nanotubes

Mechanical and thermal properties of high volume‐fraction carbon nanotube/epoxy composites, and property enhancement by UV ozone treatment of carbon nanotubes

Integration of PDA Chemistry and Surface‐Initiated ATRP to Prepare Poly(methyl Methacrylate)‐grafted Carbon Nanotubes and Its Effect on Poly(vinylidene Fluoride)–carbon Nanotube Composite Properties

Preparation and Performance of MWNTs/ Epoxy Resins Composites

Preparation and Structural Characterization for Polyacrylonitrile/Carbon Nanotubes Composites Treated with Concentrated Nitric Acid

Electrical Conductivity and Thermal Properties of Acrylonitrile‐butadiene‐styrene Filled with Multiwall Carbon Nanotubes

Fabrication and Characterization of Soluble Multi‐Walled Carbon Nanotubes Reinforced P(MMA‐co‐EMA) Composites

Effect of hydrophilically functionalized carbon nanotubes on the reinforcement of water-borne epoxy resin.

Dispersion of Multi-Walled Carbon Nanotubes Modified by Rosemary Acid into Poly(vinyl Alcohol) and Preparation of Their Composite Fibers

Effect of MWCNTs surface functionalization on the characterization of PVA/MWCNTs nanocomposites

Preparation and Characterization of Pu/Mommt Nanocomposites