Abstract:Crack sizes, geometrical configurations of specimens and structures, as well as loading conditions have significant effect on in-plane and out-of-plane constraint effects. Safety assessment with constraint effects can effectively improve the accuracy. There are prominent discrepancies between compressive fracture and tensile fracture. Most of engineering structures are usually under biaxial loading conditions, so that the influence of biaxial compressive loading on fracture analysis with constraint effects is worth paying attention. The size effect factor (relative crack length a/W, thickness to width ratio t/W and crack inclination angle β) and load factor (lateral pressure coefficient λ) of central cracked plate (CCP) specimens with I-II mixed mode crack on constraint effects under biaxial compressive loading have been investigated through theoretical analysis and finite element analysis. In-plane non-singular T-stress (T 11) and its components (T x, T y, and T xy), out-of-plane non-singular T-stress (T 33), out-of-plane constraint parameter T z and stress triaxiality factor h have been adopted to quantify constraint effects. It demonstrates that λ has remarkable influence on SIF, T 11 and T 33 under biaxial compressive loading. The effect of higher a/W (long cracks) on B 11 is more noticeable when I-II mixed mode crack is closer to pure mode II crack or pure mode I crack. The proportion of shear fracture increases under biaxial compression with λ. With the increase of β, B 33 decreases sharply and then increases rapidly with higher λ. T z can directly reflect stress states and adequately describe the loss of out-of-plane constraint. The stress state of crack tip is more likely to asymptotic plane-strain condition ahead of crack tip under compression. There are crucial differences in variation range and tendency of T z subjected to biaxial tensile and biaxial compressive loading. Moreover, T z is insensitive to λ. Stress triaxiality factor h can illustrate in-plane and out-of-plane constraint effects including size effect and load factor (sensitive to a/W, t/W, β and λ), especially can be adopted as a unified constraint parameter for long cracks under biaxial compressive loading. The in-plane T-stress components can be directly calculated by T 11 under biaxial compression. The empirical equations of K II and T 11 containing size effect and load factor simultaneously are effective and convenient for applications.

Three-dimensional analyses of in-plane and out-of-plane crack-tip constraint characterization for fracture specimens

A Modified Coffin-Manson Model for Ultra-Low Cycle Fatigue Fracture of Structural Steels Considering the Effect of Stress Triaxiality

T-stresses solution and out-of-plane constraint for central cracked plate (CCP) with I-II mixed mode crack under uniaxial compression

Instrumented indentation measurements of residual stresses around a crack tip under single tensile overloads

New Constraint Parameters Based on Crack Tip Plastic Zone: Theoretical Derivations and Effectiveness Verification

Quantification of constraint effects in elastic-plastic crack front fields

Quantifications of crack constraint effects in an austenitic steel

Quantification of crack tip constraint effect based on the critical distance

Application of modified fracture criteria incorporating T-stress for various cracked specimens under mixed mode I-II loading

Analysis of mixed-mode Compact-Tension-Shear (CTS) specimens with slanted propagating cracks

3D front tip fields in creeping solids under constraint effects: a higher-order asymptotic solution

Investigation on in-plane and out-of-plane constraint effects for plates with I-II mixed mode cracks under biaxial compressive loading

Investigation of the applicability and effectiveness of unified constraint parameters on A516 Gr70 steel specimens under ductile fracture

Numerical modelling of a new FCP model and a correlation of the FCP rate with the constraint

Fracture parameters analysis of compact tension specimens with deflected fatigue cracks: ZK60 magnesium alloy

THE ANALYSIS ON STRESS STATUS NEAR THE CRACK TIP FOR THREE POINTS BENDING SPECIMEN WITH A CRACK

A new creep-fatigue crack growth model and a correlation of the creep-fatigue crack growth rate with unified constraint parameter

EFFECT OF OUT-OF-PLANE CONSTRAINT ON DUCTILE FRACTURE TOUGHNESS

A Higher-Order Asymptotic Solution for 3d Sharp V-Notch Front Tip Fields in Creeping Solids

Characterizing the fracture forming limit curve from shear to uniaxial tension in ultrathin sheet metals using specimens with cutouts

Fracture energy and tensile strength depending on stress triaxiality along a running crack front in three-dimensional cohesive modeling