Abstract:Repairing processing is a significant method for damaged high-cost Ti-6Al-4V components to decrease economic loss, which usually utilizes a welding technique. For a large-size structural component, welding processing is commonly completed in air conditioning, which makes it difficult to avoid welding defects. To this end, an appropriate matching technique is important for improving welding performance. In the present research, asynchronized laser shock peening (ALSP) and synchronized laser shock peening (SLSP) techniques were utilized to decrease the influence of macro welding defects on laser-welded Ti-6Al-4V joints. The results show that SLSP has a greater effect on inducing surface plastic deformation on Ti-6Al-4V joints with a pitting depth of more than 25 microns while ALSP can lead to a pitting depth of about 15 microns. Through micro-CT observation a long hot crack exists in the central area of as-welded joints with a length of about 2.24 mm, accompanied by lots of pores in different sizes on double sides. After ALSP processing, some pores are eliminated while others are enlarged, and one-side crack tips present closure morphology. However, some microcracks exist on the side-wall of hot cracks. With the influence of SLSP, significant shrinkage of pores can be observed and both sides of crack tips tend to be closed, which presents a better effect than ALSP processing. Moreover, greater effects of grain refinement and thermal stress release could be achieved by SLSP processing than ALSP, which can be ascribed to dynamic recrystallization. For the as-welded joint, the ultimate tensile strength (UTS) and elongation (EL) values are 418 MPa and 0.73%, respectively. The values of UTS and EL in the ALSP processed joint are increased to 437 MPa and 1.07%, which are 4.55% and 46.48% higher than the as-welded joint, respectively. Such values after SLSP processing are 498 MPa and 1.23%, which are 19.14% and 68.49% higher than the as-welded joint, respectively.

Improvement of Damping Properties in Laser Processed Superelastic Cu-Al-Mn Shape Memory Alloys

Fabrication of Integrated Ni-Ti Alloys Possessing Both Super-elastic and Shape Memory Properties by Laser Powder Bed Fusion

Applicability of LPBF for producing Cu-11Al-5Ni-4Fe wt.% with shape memory properties

Simultaneous enhancement of mechanical and functional properties by heat-treatment in CuAlNi shape memory alloys fabricated by laser powder bed fusion

The mechanical and functional behaviors of Mn–15 wt.%Cu alloy produced by selective laser melting

Mechanical Properties of Additive Laser-Welded NiTi Alloy

Additive manufacturing of Cu-Al-Mn shape memory alloy with enhanced superelasticity

Dissimilar Laser Welding of a NiTi Shape Memory Alloy to Ti2AlNb

Study on interface and mechanical property of laser welding of NiTi shape memory alloy and 2A12 aluminum alloy joint with a TC4 wire

Microstructure and mechanical properties of Cu-Cr-Zr alloy prepared by electron beam additive manufacturing and laser-MIG hybrid welding

Achieving dual-phase structured Cu-Al-Mn-Si alloy with prominent shape memory properties via laser powder bed fusion

Thermal fatigue crack growth behavior of ZCuAl10Fe3Mn2 alloy strengthened by laser shock processing

Formation mechanism of Al-Zn-Mg-Cu alloy fabricated by laser-arc hybrid additive manufacturing: Microstructure evaluation and mechanical properties

Effect of asynchronized and synchronized laser shock peening on microstructure and mechanical properties of the Ti-6Al-4V laser joint

Martensitic transformation characteristics, mechanical properties and damping behavior of Cu–Al–Ni shape memory alloys: A review of their modifications and improvements

Improving the ductility in laser welded joints of CoCrFeMnNi high entropy alloy to 316 stainless steel

Effect of element evaporation on the microstructure and properties of CuZnAl shape memory alloys prepared by selective laser melting

Improvement of microstructure and mechanical properties of laser welded Al-Si coated 22MnB5 steel joints by austenitic element copper

Mechanical Properties and Interfacial Characterization of Additive-Manufactured CuZrCr/CoCrMo Multi-Metals Fabricated by Powder Bed Fusion Using Pulsed Wave Laser

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

Effect of Synchronized Laser Shock Peening on Decreasing Defects and Improving Microstructures of Ti-6Al-4V Laser Joint