Abstract:This research aims to study the flexural and pseudo‐ductile behavior of e‐glass biaxial and uniaxial fabric reinforced cementitious matrix (FRCM). Also, the flexural results and load–deformation curves of FRCM samples were numerically simulated using the finite element method (FEM). The experiments were started with preparation of FRCM flexural samples with different types of fabrics (biaxial and uniaxial) and their distribution in the matrix: one layer was put in the middle, two on the top, two on the bottom, and three layers were distributed equally. The surface morphology and cross‐section microstructure of the fabricated FRCM panels and cohesion of fabrics inside of them were observed using an optical microscope. Subsequently, the flexural response of the FRCM samples was measured according to standard EN 196‐1. Afterwards, based on the flexural measurements, the pseudo‐ductile behavior of the FRCM panels in terms of the ductility index (DI) was determined using energy criteria, including Naaman and Grace models. Finally, the crack propagation and flexural load‐deformation curves of FRCM samples were numerically modeled using FEM (LS‐DYNA) to validate the experiential results. The results showed that reinforcement of mortar with glass fabric leads to a significant increase in strain, especially in case of 3 layers/FRCM till 224% (uniaxial) and 110% (biaxial). Also, the uniaxial FRCM samples provided higher flexural load (3600 N) compared with mortar panel (2337 N) and biaxial FRCM (2788 N). In addition, the DI of FRCM samples was significantly improved by embedding 3 layers of uniaxial fabrics up to 152% (Naaman) and 230% (Grace), when compared with neat panel. Finally, the numerical results obtained from FEM provided a high predication to simulate the failure mode of all panels and to model the load–deformation curves with agreement >96%. Based on that, it is highly recommended to use three layers of e‐glass uniaxial fabric to reinforce the cementitious composite and to improve its flexural response.

Fabrication and Mechanical Behaviors of Cementitious Composites Reinforced by 3D Woven Lattice Sandwich Fabrics

Uniaxial Tensile Behavior of Anchored Carbon Fabric-Reinforced Cementitious Matrix Plates

Manufacturing and Flexural Testing of Woven Lattice Sandwich-Ply Laminate Composites

Influence of Fiber Type on Mechanical Properties of Lightweight Cement-Based Composites

Experimental study on mechanical behaviors of polyoxymethylene woven tube-reinforced cementitious composites

A Pull-out Equivalent Telescopic Layered Failure Model of Carbon Fiber Bundles in Seawater Sea-Sand Cementitious Matrix

Anomalous matrix and interlayer pore structure of 3D-printed fiber-reinforced cementitious composites

Mechanical behavior of waste fishing net fiber-reinforced cementitious composites subjected to direct tension

Enhancement of strength and ductility of cement-based composites by incorporating silica nanoparticle coated polyvinylalcohol fibers

Conception of multifunctional sandwich-ply laminated composites and structural implementation through woven lattice sandwich layups

Fabrication and mechanical behaviors of corrugated lattice truss composite sandwich panels

Foam-filling Techniques to Enhance Mechanical Behaviors of Woven Lattice Truss Sandwich Panels

A Textile Waste Fiber-Reinforced Cement Composite: Comparison between Short Random Fiber and Textile Reinforcement

High toughness 3D printed white Portland cement-based materials with glass fiber textile

Mechanical Testing of 3D Fabric Composites and Their Matrix Material SC-15

The flexural behaviors and mechanism of wollastonite microfiber modified ultra-high performance concrete with steel fiber from micro to macro scale

Structural Design And Experimental Research Of Woven Textile Lattice Composites: A Review

Flexural and pseudo‐ductile behavior of e‐glass uniaxial and biaxial fabric‐reinforced cementitious matrix: Experimental study and simulation

Flexural Performance of Textile Reinforced Cementitious Composite with Sprinkling Water Hardening Technique

Mechanical Properties and Failure Analysis of 3D-Woven Copper Wire/Glass Fiber Hybrid Composites

Bond and cracking behavior of tailored limestone calcined clay cement-based composites including bicomponent polypropylene fibers with enhanced mechanical interlocking