Abstract:It has been well established that the entangled molecular network facilitates the formation of shish-kebabs under flow field, however, the entangled network, usually formed by long chains, tends to disentangle due to molecular relaxation. In the present work, a small amount of lightly crosslinked polyethylene (LCPE), which can be considered as stable molecular chain networks, was added to short-chain polyethylene and then injection-molded using a modified injection molding technology-oscillation shear injection molding (OSIM), which can exert a successive shear field on the melt in the mold cavity during packing stage. The hierarchic structure of the OSIM samples was characterized through differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD) and scanning electron microscopy (SEM). It was found that the oscillation flow field promoted the formation of interlinked shish-kebabs in the intermediate layer of OSIM samples, while there are still typical spherulites in the core layer of OSLM neat polyethylene (PE). The interlinked shish-kebab structure led to remarkable mechanical enhancement from 27.6 and 810.2 MPa of conventional injection molding (CIM) samples to 42.7 and 1091.9 MPa of OSIM samples for tensile strength and modulus, respectively. More importantly, under the same flow condition, the samples containing LCPE networks (termed PEX) exhibit rich shish-kebab structure both in the intermediate and core layers. Moreover, the addition of LCPE also generated stronger interlinked shish-kebabs, in which kebabs and shishes are connected by covalent bonds, rather than topological entanglement points. This special structure leads to further reinforcement from 29.6 and 879.5 MPa of CIM PEX samples to 57.5 and 1311.7 MPa of OSIM PEX samples for tensile strength and modulus, respectively. The results demonstrated that the networks with stable entanglement points are more helpful to induce the formation of shishes under flow than those with topological entanglement points. Our results set up a new method to reinforce polymer parts by tailoring the structure and morphology.

Twisted lamellae in water-assisted injection molded high density polyethylene

Structure and Morphology of Poly(lactic Acid) Stereocomplex Nanofiber Shish Kebabs.

Formation of Interlinked Shish-Kebabs in Injection-Molded Polyethylene under the Coexistence of Lightly Cross-Linked Chain Network and Oscillation Shear Flow

Crystalline orientation of the water-assisted injection molded polypropylene

Unique crystal morphology and tensile properties of injection-molded bar of LLDPE by adding HDPE with different molecular weights

Flow-Induced Shish Nucleation in Lightly Crosslinked Polyethylene: Connecting Polymer Properties and Strain to the Final Shish-Kebab Structure

The Effect of Branched Structure on the Lamellae Evolution under Uniaxial Extension and SCG Resistance of Polyolefins

Shear-induced crystallization in a blend of isotactic polypropylene and high density polyethylene

Effects of Different Ultrahigh Molecular Weight Polyethylene Contents on the Formation and Evolution of Hierarchical Crystal Structure of High‐density Polyethylene/ultrahigh Molecular Weight Polyethylene Blend Fibers

Morphologies of metallocene-catalyzed short chain branched polyethylene single crystals formed from the melt at higher temperature

Lamellar Orientation in the Blends of Linear Low Density Polyethylene and Isotactic Polypropylene Induced by Dynamic Packing Injection Molding

Melt extension-induced shish-kebabs with heterogeneous spatial distribution of crystalline polymorphs in lightly crosslinked poly(lactic acid)

Supporting Information: Formation of Interlinked Shish-kebabs in Injection-Molded Polyethylene under the Coexistence of Lightly Crosslinked Chain Network and Oscillation Shear Flow

Melt Processing and Structural Manipulation of Highly Linear Disentangled Ultrahigh Molecular Weight Polyethylene

Morphological Distribution in Micro-Injected Polypropylene Parts in the Presence of Β-Nucleating Agent

Morphological Structure of Melt-Drawn Films of Polyethylene Containing Small Amount of Copolymerized Component

Molecular Dynamics Simulation of Shish-Kebab Crystallization of Polyethylene: Unraveling the Effects of Molecular Weight Distribution.

Structural evolution of ultra-high molecular weight polyethylene gel film stretching at different temperatures with reservation of shish crystals

Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene

Increasing lamellar twisting frequency with poly(lactic acid) segments incorporation in poly(trimethylene terephthalate) ring-banded spherulites

Shish-kebab Structure Evolution of HDPE/UHMWPE During Hot Drawing