Abstract:Many components in secondary side of pressurized water reactors (PWRs) are made of carbon steels and low alloy steels. The corrosion products produced by the flow accelerated corrosion (FAC) of these components can deposite on the surface of steam generator (SG) tubes and decrease the heat transfer efficiency of SG tubes. Moreover, the enrichment of foreign ions (e.g. Cl- and Pb2+) occurs with the sedimentation of corrosion products and causes the local environment degradation, and thus accelerates the failure of SG tubes. In order to decrease the FAC of carbon steels and low alloy steels, pH controllers are often added to adjust the pH value of secondary water. The water chemistry environment of secondary side in PWRs has experienced various treatment techniques, such as phosphate treatment, all volatile treatment (AVT), morpholine (MPH) treatment, ethanolamine (ETA) treatment, and boric acid treatment. In comparision with AVT, ETA can significantly reduce the concentration of Fe in the steam-water phase region and water supply system because of its higher alkalinity and lower molar concentration in feedwater. Due to the high resistance to corrosion and stress corrosion cracking in high temperature and high pressure water, alloy 800 is often used as steam generator tubes in nuclear power plants and thus becomes increasingly attractive among researchers. However, few studies focus on the effect of ETA on the corrosion behavior of alloy 800 in high temperature and high pressure water. This work mainly aims to investigate the corrosion behavior of alloy 800 in NaOH and ETA solutions at 300 degrees C by potentiodynamic polarization curve, electro-chemical impedance spectra (EIS), SEM and XPS. The electrochemical results demonstrate that the addition of ETA decreases the current density of anodic and cathodic reactions, and increases the corrosion potential of alloy 800. Besides, ETA addition significantly increases the resistance of inner oxide layer and makes the oxide film more compact, which increases the film resistance of alloy 800 in high temperature water. Through the morphology observation and composition analysis, it is found that ETA addition can promote the formation of Cr-rich layer and increase the ratio of chromium in the oxide films although the deposition of magnetite is enhanced on the surface of alloy 800. For stainless steels and nickel-based alloys in high temperature water, the Cr-rich oxide layer can inhibit the diffusion process of 0 and metal ions, and reduces the corrosion rates of alloys. Therefore, the corrosion resistance of alloy 800 is enhanced after ETA is added in high temperature water.

Influence of Temperature on Electrochemical Behavior and Oxide Film Property of Alloy 800 in Hydrogenated High Temperature Water

Effect of temperature on corrosion behavior of alloy 690 in high temperature hydrogenated water

Corrosion Behavior of Alloy 800 in Naoh and Eta Solutions at 300 Degrees C

Investigation on the corrosion behavior of Alloy 800H at various levels of deformation

On the Stress Corrosion Crack Initiation Behaviour of Alloy 800 in High-Temperature Hydrogenated Water

Corrosion behavior for Alloy 690 and Alloy 800 tubes in simulated primary water

CORROSION BEHAVIOR OF NUCLEAR GRADE ALLOYS 690 AND 800 IN SIMULATED HIGH TEMPERATURE AND HIGH PRESSURE PRIMARY WATER OF PRESSURIZED WATER REACTOR

Influence of Annealing Temperature on Susceptibility to Intergranular Corrosion of Incoloy 800 Alloy

The Evolution of Electrochemical Behaviour and Oxide Film Properties of 304 Stainless Steel in High Temperature Aqueous Environment

Effects of alternating dissolved oxygen and dissolved hydrogen on the corrosion behavior of alloy 52 in high temperature high pressure water

Influence of Zn on Oxide Films on Alloy 690 in Borated and Lithiated High Temperature Water

Microstructural understanding of the oxidation and inter-diffusion behavior of Cr-coated Alloy 800H in supercritical water

Influence of Alloying Element on Corrosion Behavior of Hastelloy C-276 in Supercritical Water

Corrosion Behaviors of Zr-Sn-Nb-Fe-Mo Alloys in Pure Water at 360 °C/18.6 MPa: Influence of Annealing Temperature on the Anti-Corrosion Properties

Influence of Conductivity on Corrosion Behavior of 304 Stainless Steel in High Temperature Aqueous Environment

Effect of Heat Treatment on the Microstructure and Corrosion Resistance of Al0.75CoCr1.25FeNi High-Entropy Alloys

Influence of Later-Dissolved Oxygen on Microstructural Changes in Oxide Films Formed on Alloy 690TT in Hydrogenated Primary Water

Effect of Temperature Treatment on Microstructure and Electrochemical Properties of 6061 Aluminum Alloy

Effects of cold work on the corrosion behavior of Alloy 800H exposed to aerated supercritical water

Effects of heat treatment on corrosion fatigue and stress corrosion crack growth of additive-manufactured Alloy 800H in high-temperature water

Impact of Diffusible Hydrogen on Corrosion of Alloy 600 at 288°C: an In-Situ Electrochemical Study