Abstract:Due to the advantages of low cost, easy fabrication, mechanical flexibility, the research on organic solar cells has attracted a lot of attentions in the last decades. Among countless organic materials, the most successful ones are conjugated polymers, which were widely used in bulk heterojunction (BHJ) in conjugation with the fullerene [1]. In view of the fact the interpenetratedphase-separated p-n composites offer more chances for excitons to reach the p-n interfaces, BHJ greatly facilitates the dissociation of photogenerated excitons before decaying to ground state. During exciton dissociation process, the exciton delocalization at an ultra fast timescale has been observed recently, which has considerable effects on the charge generation and device performance. In this work, based on the recent studies [2–4], we established a theoretical model of polymer solar cells (PSCs) incorporating the exciton delocalization process. Through the model, we found the increase of delocalized excitons (compared to the total generated excitons) will significantly improve the short-circuit current, open-circuit voltage, fill factor and power conversion efficiency of PSCs. Particularly, the saturations of fill factor and open-circuit voltage are also observed, and the saturation points depend on the active layer thickness and recombination rate. For instance,the device model of 200nm thickness active layer has the saturated fill factor at 70% delocalization ratio, which is close to the conventional ratio of practical devices. The device configuration studied comprises a BHJ active layer sandwiched between a transparent anode and a metal cathode. Moreover, the active material is a mixture of OC 1 C 10 -PPV, as the donor, and PCBM, as the acceptor [5]. The generation rate of excitons is assumed to be homogeneous. The model proposed involves both the drift-diffusion model for photocarriers (Eq. (1)) and the diffusion and dissociation model for excitons (Eq. (2)). The governing equations are given as follows equation where q is elementary charge, n(p) is the electron (hole) density, and r G , r R are the parametersfor controlling exciton generation and bulk recombination, respectively. E is the internal E-field. µ and D are the mobility and diffusion coefficients. The exciton density is denoted by X diff and k diss is the exciton dissociation rate. The recombination R is taken to be a bimolecular form,with the rate given by Langevin [6], and η s is 0.25 for the singlet excitons. Using the physical parameters given by experiments [5], the nonlinear governing equation sets are solved self-consistently. The excitons are delocalized at an ultra fast timescale to form electron-hole pairs, which is much faster than the photo carrier relaxation time and exciton diffusion time. Consequently, the delocalization process was simulated by directly inserting the delocalization ratio η del into the equations.

Ultrafast Exciton Dissociation in Block Copolymer toward Efficient Single Material Organic Solar Cells

The Role Of Exciton Delocalization In The Performance Of Bulk-Heterojunction Polymer Solar Cells

Enhanced Intramolecular Hole Transfer in Block Copolymer Enables >15% and Operational Stable Single-Material-Organic Solar Cells

Enhanced Intramolecular Hole Transfer in Block Copolymer Enables >15% and Operational Stable Single‐Material–Organic Solar Cells

A conjugated donor-acceptor block copolymer enables over 11% efficiency for single-component polymer solar cells

Ultrafast Hole Transfer Mediated by Polaron Pairs in All-Polymer Photovoltaic Blends

Polymer-Quantum Dot Composite Hybrid Solar Cells With A Bi-Continuous Network Morphology Using The Block Copolymer Poly(3-Hexylthiophene)-B-Polystyrene Or Its Blend With Poly(3-Hexylthiophene) As A Donor

Ultrafast Electron Transfer in Low‐Band Gap Polymer/PbS Nanocrystalline Blend Films

Improved Charge Generation via Ultrafast Effective Hole‐Transfer in All‐Polymer Photovoltaic Blends with Large Highest Occupied Molecular Orbital (HOMO) Energy Offset and Proper Crystal Orientation

Narrow‐Bandgap Single‐Component Polymer Solar Cells with Approaching 9% Efficiency

Alkoxythiophene Directed Fibrillization of Polymer Donor for Efficient Organic Solar Cells

A High‐Mobility Low‐Bandgap Copolymer for Efficient Solar Cells

Efficient Hole Transfer via Delocalized Excited State in Small Molecular Acceptor: A Comparative Study on Photodynamics of PM6:Y6 and PM6:ITIC Organic Photovoltaic Blends

Acetal- and Aldehyde-Substituted Thiophene-Benzodithiophene Copolymers for Organic Solar Cells

Hybrid Block Copolymer/Perovskite Heterointerfaces for Efficient Solar Cells

High Efficiency Polymer Solar Cells with Efficient Hole Transfer at Zero Highest Occupied Molecular Orbital Offset Between Methylated Polymer Donor and Brominated Acceptor.

Efficient and Stable Quasiplanar Heterojunction Solar Cells with an Acetoxy-Substituted Wide-Bandgap Polymer

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Design and Synthesis of Wide-bandgap Conjugated Polymers Based on 3,4-Dicyanothiophene for Efficient Organic Solar Cells

A benzo[ghi]-perylene triimide based double-cable conjugated polymer for single-component organic solar cells

Tradeoff between Intermolecular Interaction and Backbone Disorder by High Molecular Dipole Block for Improving Blend Morphology of Polymer Solar Cells